Audiovox TRAN-410A - Manual (Page 7)

To Lock the Unit
Press
IFUNCI
, then key [T] (LOCK).
The
[LOCKI
indicator lights. The unit will remain
locked until unlocked, even if the power is turned off.
Automatic Lock (NAM Option)
If you request it, your NAM can be changed so your
unit will automatically go into the locked condition
when you disconnect the cigarette lighter adaptor.
When the TRAN - 55A is plugged in again, the un­
lock code is required to operate the phone.
To Unlock the Unit
Enter the three-digit unlock code. The
LOCK]
indica­
tor will go out when the three-digit code is the same
as the code registered in the NAM.
Backlighting On/Off Control
LCD display and the keypad are backlit automati­
cally after the Power-On. If needed, backlighting can
be turned off by pressing
jRCLj
, key then .
Even if the unit is in the backlighting “Off” mode, the
backlighting will be turned on again automatically
for 10 seconds when any key operation is performed
or a call is received.
To return to the backlighting “On” mode, press
jRCL|
, key then [§ again.
Volume Control
The audio level of the loudspeaker, earpiece and the
alert tone can be adjusted by the Volume Control
keys ( 0 and
[V]
).
• Loudspeaker: Leave the handset in the cradle:
To increase—Keep pressing 0 key until you get
the desired sound level.
To decrease—Keep pressing [V] key until you get
the desired sound level.
Sound level will be displayed on the readout digitally
during the level adjustment and the sample tone will
indicate the sound level when you are not engaged in
a telephone conversation. The display format is as
follows:
SPK □ □ (1 to 10)
• Handset: Lift the handset and perform the same
procedures as above.
In this case, the display format is as follows:
H.s m (1 to 10 )
• Alert Tone; Press
|RCL|
. key then .
Then adjust the alert tone level in the same manner
as above. Your telephone will ring at the new level.
In this case, the display format is as follows:
ALT I I (1 to 10)
PLACING TELEPHONE
CALLS
To Place a Call
1. Enter the phone number with the handset on-hook
or off-hook. The last 15 digits of the dialed num­
ber are displayed on the readout.
Note: After 120 sec., display will return to the
10-digit display mode.
2. If a dialing error is made, press
ICLRI
, then enter
the phone number again. Pressing
ICLRj
momen­
tarily (less than approx. 0.5 sec.) clears only the
last digit.
3. Press
|SND
. The i
IN USE
j indicator will light. You
may lift the handset from the cradle either before
or after the called party answers to proceed with
your conversation.
Note: If assigned in NAM, the phone number can be
pre-set up to 32 digits. However, in this case
it is necessary to confirm with system opera­
tor whether such service is available or not.
If the Call Fails to Go Through
1. If you hear the “reorder” signal, press
[END|
, then
if there were no dialing errors, press
|SND
for
redial. (Redialing w'ith digit keys is not necessary.)
2. If the “intercept” signal is heard, press
|ENDj
, then
redial the correct number.
Automatic Redial (NAM Option)
If the feature of Automatic Redial (NAM Option) is
selected, your unit will automatically make five
attempts to reach the cell site if the first try is not
successful. The j
IN USE]
indicator will stay on, but
the speaker will be muted for twenty seconds.
This is done so that you do not hear the reorder
signals from the loudspeaker. If you need to termi­
nate the automatic redial, press
|END| .
Terminating a Call (Hanging Up)
Press
|END|
, or replace the handset in the cradle.
The |T n use
\
indicator w’ill go out.
If Hands-free is activated in NAM, you have to press
12 13