Ashly FET-1500C - Manual (Page 2)

Specifications
■
POWER OUTPUT
ElA SPECIFICATION
(±1dB <1% THD 20Hz-20kHz)
STEREO (Rated Per Channei)
4 ohms: 300 Watts RMS
8 ohms: 200 Watts RMS
MONO BRIDGED
8 ohms: 600 Watts RMS
FTC SPECIFICATION
(min power <.01% SMPTE IMD)
STEREO (Rated Per Channel)
4 ohms: 275 Watts RMS
8 ohms: 175 Watts RMS
MONO BRIDGED
8 ohms: 550 Watts RMS
Total Harmonic Distortion: .004% 1kHz,8D
.01% 20Hz,8ii
.05% 20Hz-20kHz,8l2
IM Distortion (SMPTE): .004% 8£2
(IHF): .01%8i2
Damping Factor: >100 20Hz-20kHz
Bandwidth: 100kHz
Slew Rate: 50V/MS
Frequency Response: ± .5dB 10Hz-50kHz
Rise Time: 2| t S 10%-90%
Full Power Input Sensitivity: 1.3V
Hum and Noise: >110dB below full output
Power Requirements: 110-125VAC, 50-60HZ
Size: 19"Lx3.5"H X 16"D
Shipping Weight: 47 lbs
Architect’s Specification
Ashly Model 1500M
The power ampllller, being of iwo ehanncls. shall deliver a
minimum power of 175 watts per channel into 8 ohm
loads or 275 watts per channel Into 4 ohm loads with both
channels operating. When switched into bridged mono
mode, it shall deliver at least 550 watts into an 8 ohm
load. The amplifier shall be Immune to damage from
shorted, open, or mismatched loads. The ampliner shall
have a gain of 29dB ± ,5dB |jcr rhannel and an input sen­
sitivity of 1.3 Volts ± 2% for full rated output. Frequency
response shall be lOHz to 20kHz ± ,5dB, It shall be stable
Inlo any load including pure capacitors and inductors.
Hum and noise shall be at least 1 lOdB below full output
and SMPTE intermodulation distortion shall be less than
.01% at full output. The amplifier shall have rear panel
switching for mono and bridging modes and rear mounted
level controls. The Inputs shall be balanced bridging type
tvlth male and female XLR type connectors as well as 1/4"
phone Jacks. A three-color LED type indicator shall be
employed to show the power level of each channel and self
contained forced air cooling shall be used. The power out­
put devices sliall be of the Lateral MOS-FET type. The
amplifier shall weigh 371b. net and mount in a standard
19 inch rack using two spaces (3.5' high). The power
requirement shall be 110-125VAC. 50-6011Z.
Tlie power amplifier shall be an Ashly FET-1500M.
Ashly Model 1500C
The power amplifier, being of two channels, shall deliver a
minimum power of 175 walls per channel into 8 ohm
loads or 275 walls per channel Inlo 4 ohm loads with both
channels operating. When switched into bridged mono
mode, it shall deliver at least 550 walls Into an 8 ohm
load. The amplifier shall be immune to damage from
shorted, open, or mismatched loads. The amplifier shall
have a gain of 29dB ± .5dB per channel and an input sen-
silhily of 1.3 Volts ± 2% for full rated output. Frequency
response shall be lOHz to 20kHz ± ,5dB. It shall be stable
into any load including pure capacitors and inductors.
Hum and noise shall be at least
1 lOdB below full oiilpul
and SMPTE intermodulation distortion shall be less than
.01% at full output. The ampllllcr shall have rear panel
switching for mono and bridging modes and rear mounted
level controls. The inputs shall utilize 1/4" phone Jacks as
well as tcrminal/barrier input strips. Self contained forced
air cooling sliall be used. The power otitpnl dcvlce.s shall
be of the Lateral MOS-FET type. The amplifier shall weigh
371b. net and mount in a standard 19 Inch rack using two
spaces (3.5" high). The poiver requirement shall be 110-
125VAC, 50-60HZ.
Tlie powei amplifier shall be an Ashly FET- 1500C.
To provide maximum fiexibility,
Ashiy offers two variations in our
FET Power Ampiifiers:
The FET-1500M (top) features XLR
and 1/4" inputs.
The FET-1500C (bottom) utiiizes
Barrier Strips and 1/4" inputs.
Ashly Audio Inc.
ASHL-Y
Since 1972
© 1989 Ashly Audio