ADT Security Services Commercial Fire & Burglary Alarm System FOCUS 200 PLUS User Manual

Security system

Text mode
Original mode

ADT Security Services Commercial Fire & Burglary Alarm System FOCUS 200 PLUS User Manual | 88 pages

Table of contents

Document Outline

Introduction
FOCUS® 200 PLUS Features
Control Unit
Operating Panel
Protection Points and Groups
User Access and Security
Automated Event Recording and Printing
Summary
Introduction
Introduction
Operating Panel Functions
Normal Inactive Screen
Responding to Alarms
Viewing Current Alarms
Entering Your Personal ID Number
- EXERCISE: PANEL ACTIVATION/DEACTIVATION
The Navigational Menu Selections
- EXERCISE: THE MORE/FIRST SELECTION
Turning BA Groups Off
Action Menus 1-4 - Main Features
Action Menu 1
- EXERCISE: THE “?” SELECTION
- EXERCISE: LESSON
- EXERCISE: SEE ALARMS
- EXERCISE: TURN ON BURGLARY PROTECTION
Action Menu 2
- EXERCISE: SEE POINTS
- EXERCISE: TEST
Action Menu 3
- EXERCISE: BYPASS/UNBYPASS PROTECTION POINTS
- EXERCISE: HISTORY LOG
Action Menu 4
- EXERCISE: NAME PNT/GPS
Summary
Operating Panel
- Note: If you enter 18 incorrect digits, the operating panel will go into “lockout,” preventing further entries for 60 seconds.
Action Menus
Action Menu 1
Action Menu 2
Action Menu 3
Action Menu 4
Introduction
- Note: Certain system features and functions must be controlled from the ADT Customer Monitoring Center. Prior to modifying your system, it is advisable to check with your ADT Service Representative.
User Data
- Note: Upon installation or initial system setup, one user (e.g., System Manager) will be assigned the “Privilege Level” to perform the following functions:
- • Open outside of the schedules (Irregular open).
- • Bypass burglar alarm (BA) protection points.
- • Change temporary schedules.
- • Change permanent daily schedules and the real-time.
- • Change, add, and delete user names, ID codes, card/key codes, cancel dates, and “Privilege Levels” for users.
Entering or Changing a User Name
User Selection Menu
Deleting a User ID Code
User Selection Menu
Assigning or Changing User Access
User Seiection Menu
- Note: To change the privilege level of a user, an ID code must have this capability assigned to it during the initial setup and programming of the
- system by ADT.
- Note: If this user number has an existing ID code, the existing four-digit PIN will not be displayed.
Changing the Time and Date
- Note: Before changing the time or date, turn off all BA groups.
Time Selection Menu
- Note: Change will not appear unless all BA groups are off.
- Note: Those users who have been assigned only the privilege level of “Change temp sched” are limited to time changes within 5 minutes of the current time displayed on the screen.
- Note: Before changing the time or date, turn off all BA groups.
Daily Operating Schedules
Time Selection Menu
- If Auto On/Off feature has been selected, see Changing Auto On/Off
Time Selection Menu
Holiday Description and Dates
Time Selection Menu
Group/Point Descriptions
- Note: Group descriptions will be displayed first. Press the Next button to scroll through the group descriptions and begin display of point descriptions.
Turning On Burglary Protection
- Note: If you do not exit the protected area prior to the expiration of the exit delay, an “exit fail” signal will be transmitted to the ADT Customer Monitoring Center.
Action Menu 1
Turning Off Burglary Protection
Turn Off Menu
- Note: If the green lamp does not light and the red lamp “winks” out momentarily, it indicates the system is rejecting the access attempt.
System History Log
History Selection Menu
Bypassing/Unbypassing Burglary Protection
- Note: A bypassed point cannot detect intrusion or an alarm condition. Before resorting to bypassing a point, attempt to repair or correct the problem.
Bypass Selection Menu 1
Group Selection Menu
Bypass Selection Menu 2
Extending Close Time
Sending Messages to a Pager
Burglary Protection Points (Audible)
Protection Points (Visuai)
Protection Groups
Testing Holdup, Fire, and Supervisory Devices
- Caution: Use care when conducting this test. All holdup, fire, and
- supervisory functions are disabled during this test mode. In the event of a
- security breach or fire, no signals will be sent to the monitoring center.
Bell and Operating Panel Display
- Note: A test pattern of all LCD elements will be shown for 4 seconds, and
- the bell will ring for the last 4 seconds of this 30-second test. Walk to an
- area where the bell can be heard to verity its operation.
- Trouble or Error Display System has battery power only.
- Cannot turn on! AC power is off.
- Description
- Action
About Fire Alarm Codes
Code Enforcement
ADT’s FOCUS 200 Plus Fire Alarm System Capabilities
- LIMITED WARRANTY
- Terms and Conditions Applying to Sale of Equipment
- ADT Security Services, Inc. One Town Center Road Boca Raton, FL 33486