Ashly FET-2000M - Manual (Page 2)

Specifications
• „■' J-:
s
I
Architect’s Specification
Ashly Model 2000M
The power amplifier, being of two channels, shall deliver a
minimum power of 250 waits per channei into 8 ohm loads.
400 watts per channei Into 4 ohm ioads. or 600 watts per
channel Into 2 ohm loads with both channels operating.
Wlicn switched into bridged mono mode, it shall deliver at
least 500 watts into a 16 ohm load. 800 watts into an 8
ohm load, or 1200 walls into a 4 ohm load. Tlie amplifier
shall be Immune to damage from shorted, open, or mis­
matched loads. The amplifier shall have a gain of 29dB t
.5dB per channel and an input sensitivity of 1.7 Volts ± 2%
for full rated output. Frequency response shall be lOMz to
20kllK ± .5clB. It shall be stable into any load including
pure capacilors and inductors. Hum and noise shall be at
least 1 lOdB below full output and SMPTE intermodulation
distortion shall be less than .01% at full output. The ampli
fier shall have rear panel switching for mono and bridging
modes and rear mounted level controls, Tlic Inputs shiUl be
balanced brinectors as well as 1/4" phone jacks. A three-color LED type
indicator shall be employed to show the power level of each
channel and self contained forced air cooling shall be used.
The power output devices shall be of the Lateral MOS-FETl'
type. The amplifier shall weigh 551b. net and mount In a
standard 19 Inch rack using three spaces (5.25" highj. The
power requirement shall be 110-125VAC. 50-60Hz.
Tile power amplifier shall be an Ashly FET-2000M.
Ashly Model 2000C
Tile power amplifier, being of two channels, shall deliver a
minimum power of 250 watts per channel Into 8 ohm loads.
400 watts per channel into 4 ohm loads, or 600 walls per
channel into 2 ohm loads with both channels operating.
When swiichcd into bridged mono mode, it shall deliver at
least 500 watts Into a 16 ohm load. 800 watts Into an 8
ohm load, or 1200 watts into a 4 ohm load. The amplifier
shall be immune to damage from shorted, open, or mls-
malched loads. The amplifier shall have a gain of 29dD ±
,5dB per channel and an input sensllhily of 1.7 Volls ± 2%
for full rated output. Frequency response shall be lOHz to
20kHz ± ,5dB. It shall be stable into any load including
pure capacitors and inductors. Hum and noise shall be al
least 1 lOdB below full output and SMPl'E Intermodulation
distorlion shall be less Ilian .01% at lull output. The ampli­
fier shall have rear panel switching for mono and bridging
modes and rear mounted level controls. The inputs shall
utilize 1/4" phone Jacks as well as barrier/termlnal Inpiil
strips. Self contained forced air cooling shall be used. The
power output devices shall be of the Lateral MOS-FIiTr type.
The amplifier shall weigh 551b. net and mount in a stan­
dard 19 inch rack using three spaces (5.25" high}. The
power requirement shall be 110-125VAC. 50-60Hz.
The power amplifier shall be an Ashly FET-2000C,
To provide maximum flexibility, Ashly
offers two variations in our FET Power
Amplifiers:
The FET-2000M (top) features XLR and
1/4" inputs.
The FET-2000C (bottom) utilizes Barrier
Strips and 1/4" inputs.
Ashly Audio Inc.
Since 1972
© 1989 Ashly Audio