Maintenance, Depth adjusting ring, Adjustments or replacement (continued) – Sears 315.17473 User Manual

Page 13: Accessories, Page 13

Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".

MAINTENANCE

DEPTH ADJUSTING RING

ADJUSTMENTS OR REPLACEMENT (Continued)

5. Remove two screws on front of depth adjusting ring. Also remove slide nut from pocket inside clamping lever. NOTE:

Depth adjusting ring replacement Is the only time bottom screw should be removed.

‘

Remove depth adjusting ring.

Position new depth adjusting ring in place and secure with the same screws and slide nut used to secure old depth

adjusting ring.

Make all adjustments with top screw (#10-32 x 15/16 In. Fil. Hd.) as mentioned previously. Bottom screw (#6-19 x

1/2 In. Pan Hd.) should have up to a maximum 1/4 In. (.250) clearance, allowing flexibility for top screw adjustments
See Figure 19.

__________________

6.
7.

REAR OF DEPTH

ADJUSTING RING

Fig. 18

1/4 IN. (.250) MAXIMUM

CLEARANCE

FRONT OF DEPTH

ADJUSTING RING

Fig. 19

ACCESSORIES

THE FOLLOWING RECOMMENDED ACCESSORIES ARE CURRENT AND WERE
AVAILABLE AT THE TIME THIS MANUAL WAS PRINTED.

Dovetail Template
Box Joint Template
Mill-Works Molding Maker
Bis-Kit Plate Jointer Kit

Multi-Purpose Router Guide

(9-2579)
(9-2580)

(9-25254)
(9-25423)
(9-25179)

Template Guide Bushings

Rout-A-Form Pantograph

Template Set
Sharpening Kit

Full View Router Base

(9-25082)
(9-25187)

(9-2573)

(9-66501)
(9-25086)

COMBI

NATION

PANEL

CUTTER

M33S-1/4'

' 2S541-3/B'

VBNINQ

BITS

26330-1/8*
28326-3/16*

28326- 7/32*
28327- 1/4*

DOUBLE END

48*. 60*

V-OROOVE

28333

CORE BOX

BIT

28328-1/4*

28328-1/2*

V-QROOVE

CHAMFER

28322-1/2-

‘25878-1/2*

STRAIGHT

FACE

BITS

26317-1/1®*
26316-1/6*

26315-1/4*

26314-3/6*

26313-1/2*

26312-3/4*

*25624-1/4*
*25528-5/16*
*25626-3/8*
•25827-1/2*
*25606-3/4*

COMBI

NATION

STRAIGHT,

BEVEL

CUTTER

FORFORMCA

•2541

VENEER

CUTTER

STRAIGHT

•25413

BEVEL
•25412

HINGE

MORT1S1NQ

BIT

OOVETAH.

CUTTER

BfTS

26336

26319-1/4*

26316-1/2*

RABBET

BIT

OGEE

3/16"

26305

1/4",5/16-,

ROMANO

26304-5/32"

26306-1/4"

26310

•25582

•25507-5«2"

*25504-1/4"

•CARBIDE TIPPED'BITS

COVE

BIT

26301-3/8*
26300-1/2"

*25576-3/8"

•25575-1/2"

CHAMFER

BIT

26303

BEAD

QUARTER-

ROUND

BITS

26309-1/4"

26308-3/8"

26307-1/2"

•25503-1/4"

•255664/8"
•25565-1/2*

ARBOR

2689

;

WITH 2

BALL

BEARINGS

(1/2 s B/e**)

*25895

The use of attachments or accessories not listed above might be hazardous.

Page 13