TeeJet RX510 - Manual (Page 2)

1.969 in
(50.00 mm)
3.937 in
(100.00 mm)
8.217 in
(208.70 mm)
0.402 in (10.20 mm)
Opening
R2.01 in
(5.10 mm) TYP.
0.492 in
(12.5 mm)
TYP.
www.teejet.com 98-01405 R0 US
USER GUIDE TEEJET TECHNOLOGIES
GETTING STARTED
This guide provides the information you need to set up and begin using your new RX510,
a combined L1+L2 GNSS receiver and antenna, with L-band support and Emulated Radar (ER) output.
9.2 in
234 mm
9.2 in
234 mm
3.5 in
89 mm
Additional NMEA outputs are available, please contact TeeJet Technical Support for details.
RX510 LEDs
LEDs on the front of the RX510 provide basic receiver status information. The operation of the LEDs on the RX510 is summarized in the
following table:
Red Yellow Green Condition
Off Off Off Power is not available. (Red indicator may also not be lit if a boot failure has occurred.)
On Off Off Power available but no satellites are being tracked
On Flashing Off Tracking at least one satellite but not a valid position
On On Off Position valid in basic autonomous mode
On On Flashing SBAS tracking, but not enough data for enhanced solution
On On On Position valid in an enhanced accuracy mode* (WAAS/EGNOS/MSAS/DGPS,
OmniSTAR VBS/XP/HP, or RTK)
On Flashing Flashing Fixed position with bad integrity
* When acting as a reference receiver, all lights on solid indicates a good fixed position.
OMNISTAR® SUBSCRIPTION
To subscribe to OmniSTAR XP or HP:
1. Power on the RX510.
2. Before you call OmniSTAR, find a clear view of the sky towards the equator that will be available before and approximately 45 minutes after
completing the subscription purchase from OmniSTAR.
3. Before you call OmniSTAR, find the 6-digit OmniSTAR Serial Number (OSN) on the RX510 shipping box.
4. Call OmniSTAR Customer Service (1-888-883-8476 in North, Central and South America) to start the subscription.
• Pricing information is available at: http://omnistar.com/pricing.html
• If you intend to use GLONASS together with GPS, you will need to specify the G2 subscription.
• OmniSTAR will require a credit card number for subscription charges.
• OmniSTAR will ask for the OmniSTAR Serial Number, and when they ask for the Manufacturer, tell them "Manufacturer ID 007"
Depending on your location, the OmniSTAR service you subscribed to, and the satellite information reported by the device you are connected
to, you may see the Station ID number (PRN number) change to somewhere in the range of 1000 to 1021 once the subscription is received
and the convergence process begins. It may take up to 45 minutes for complete OmniSTAR XP/HP convergence to take place and the GGA
Quality Indicator to transition to a value of "5", during which time the Station ID number (PRN number) may change several times.
MOUNTING INSTRUCTIONS
Intermediate Mounting Plate Template
A template for the intermediate mounting plate has been drawn in the
background of this user guide.
• Red lines indicate holes where attachement will occur.
• Green lines indicate the outline of the mount and other holes for attaching
the release plate.
Figure 1-1: Intermediate Mounting Plate
The universal mounting plate can be used in several configurations:
• Stand-alone plate that is hard-mounted onto the implement
• Hard-mounted onto an intermediate plate
• As part of the quick-release kit
The mounting holes in the RX510 will align with the dimple locations in the
universal mounting plate. You can use Metric or Imperial Countersunk head
bolts as follows:
• Metric .............Quantity 4 M6x 1.0mm bolts no longer than 15mm
• Imperial ..........Quantity 4 1/4-20 bolts no longer than 1/2"
Figure 1-2: Complete Mounting Kit
Intermediate
Mounting Plate
Universal Mounting Plate Quick Release Latch
Mounting Considerations
• Choose a location that has a clear view of the sky so that each satellite
above the horizon can be tracked without obstruction.
• When mounting the RX510 Receiver, a space of at least 6″ (15 cm) between
the receiver and any bend in the cable is required. Any length shorter than 6″
puts undue stress on the cable and the enclosure for the RX510.
• The receiver should not be mounted where water can pool around it. The
receiver housing is designed to withstand rain and splashing, but not
submersion in liquids for sustained periods of time.
• Mount the receiver above all other metal objects to avoid multipath. Satellite
signals received by the GPS receiver by a reflection from an object can
decrease positioning accuracy. For example, roof racks, large headlight
enclosures, etc., can cause multipath that may result in a jump in GPS
position.