Interlogix NX-1700E - Manual (Page 12)

VIII. PROGRAMMING WORKSHEETS IMPORTANT TIP:
Defaults are shown in bold italics.
LOC PG DESCRIPTION DEFAULT YOUR DATA
0 7 SCAN FUNCTIONS
Seg 1 SINGLE SCAN FUNCTION (1 Beep) 8
1 = "On" to send Code Entry function to the control panel.
2 = "On" to activate the Armed Away mode.
3 = "On" to activate the Armed Stay mode.
4 = "On" to send the Disarm function to the control panel.
5 = "On" to send Auxiliary Function #1 to the control panel.
6 = "On" to send Auxiliary Function #2 to the control panel.
7 = "On" to broadcast an X-10 function (Loc 241 for programming).
8 = "On" to send an RTE; and activate the onboard open collector output.
Seg 2 DOUBLE SCAN FUNCTION (2 Beep) 1
1 = "On" to send Code Entry function to the control panel.
2 = "On" to activate the Armed Away mode.
3 = "On" to activate the Armed Stay mode.
4 = "On" to send the Disarm function to the control panel.
5 = "On" to send Auxiliary Function #1 to the control panel.
6 = "On" to send Auxiliary Function #2 to the control panel.
7 = "On" to broadcast an X-10 function (Loc 241 for programming).
8 = "On" to send an RTE; and activate the onboard open collector output.
Seg 3 SINGLE SCAN HOLD FUNCTION (3 Beep) 1
1 = "On" to send Code Entry function to the control panel.
2 = "On" to activate the Armed Away mode.
3 = "On" to activate the Armed Stay mode.
4 = "On" to send the Disarm function to the control panel.
5 = "On" to send Auxiliary Function #1 to the control panel.
6 = "On" to send Auxiliary Function #2 to the control panel.
7 = "On" to broadcast an X-10 function (Loc 241 for programming).
8 = "On" to send an RTE; and activate the onboard open collector output.
1-240 8 RESERVED
241 8 X-10 ADDRESS
Seg 1 MODULE NUMBER 0
Seg 2 HOUSE CODE 0
NX-1700E Card Reader 12
(see chart)
X-10 ADDRESS CODES
0=A 4=E 8=I 12=M
1=B 5=F 9=J 13=N
2=C 6=G 10=K 14=O
3=D 7=H 11=L 15=P
Seg 3 SINGLE SCAN FUNCTION (1Beep) 2
0 = All units off
1 = All lights on
2 = On
3 = Off
4 = Dim
5 = Bright
6 = All lights off
8 Seg 4 DOUBLE SCAN FUNCTION (2 Beep) 3
0 = All units off
1 = All lights on
2 = On
3 = Off
4 = Dim
5 = Bright
6 = All lights off
Seg 5 SINGLE SCAN HOLD FUNCTION (3 Beep) 2
0 = All units off
1 = All lights on
2 = On
3 = Off
4 = Dim
5 = Bright
6 = All lights off
242 8 OPTIONS AND READER PARTITION
Seg 1 SYSTEM OPTIONS 3, 5, 6
1 = "On" if enabled for User Card Programming
2 = "On" if optical tamper enabled
3 = "On" if buzzer follows keypad buzzing
4 = "On" if ding-dong chime enabled (Opt 3 & chime must be enabled)
5 = “On” if an RTE from a scanned card is to be logged as Code Entry
6 = “On” if reader is in NX-1700E Legacy Mode
7 = “On” if an RTE from a zone or the Egress input is to be logged as Code Entry.
8 = “On” if LED extinguish after 2 minutes without a scan.
Seg 2 LED1 (GREEN) OPTIONS 1,2
1 = "On" follows system Ready status
2 = "On" to toggle with the Open Collector output
3 = "On" if inverted
4 = 4-8= Reserved.