Interlogix NX-1700E - Manual (Page 11)

NX-1700E Card Reader 11
L OCATION 271 P ROGRAMMING THE D ATE OF H OLIDAYS IN J ANUARY
(8 segments of numerical data) Program the day of the month in January that the Opening time in a schedule is suppressed. For
example, if the opening should not occur on January 1, program a “1” in Segment 1. This feature can be repeated up to a maximum
of 8 holidays per location (month). (Default is No holidays)
L OCATIONS 272 - 282 P ROGRAMMING THE D ATE OF H OLIDAYS FROM F EBRUARY TO D ECEMBER
(8 segments of numerical data) Locations 272 - 282 are used to program the day of each month, from February to December, in
which the Opening time in a schedule is suppressed. Each location will accommodate up to a maximum of 8 holidays, and
programmed with the same steps as Location 271 described previously.
Location 272 – February holidays
Location 273 – March holidays
Location 274 – April holidays
Location 275 – May holidays Location 276 – June holidays
Location 277 – July holidays
Location 278 – August holidays
Location 279 – September holidays Location 280 – October holidays
Location 281 – November holidays
Location 282 – December holidays
Location 283
Programming Activation Data for User Cards 1 through 120
(15 segments of binary data) This location is used to select which user cards 1 - 120 are activated. If the LED is “on”, the card is
active. Each segment has 8 LEDs corresponding to the 8 possible user cards. Example: Segment 4, LED2 indicates that user card
26 is active.
SEG USER
CARDS
SEG USER
CARDS
SEG USER
CARDS
SEG USER
CARDS
SEG USER
CARDS
1 1 - 8 4 25 - 32 7 49 - 56 10 73 - 80 13 97 - 104
2 9 - 16 5 33 - 40 8 57 - 64 11 81 - 88 14 105 - 112
3 17 - 24 6 41 - 48 9 65 - 72 12 89 - 96 15 113 - 120
L OCATION 284 P ROGRAMMING A CTIVATION D ATA FOR U SER C ARDS 121 THROUGH 240
(15 segments of binary data) This location is used to select which user cards 121 - 240 are activated. If the LED is “on”,
the card is active. Each segment has 8 LEDs corresponding to the 8 possible user cards. Example: Segment 15, LED8
indicates that user card 240 is active.
SEG USER
CARDS
SEG USER
CARDS
SEG USER
CARDS
SEG USER
CARDS
SEG USER
CARDS
1 121 - 128 4 145 - 152 7 169 – 176 10 193 - 200 13 217 - 224
2 129 - 136 5 153 - 160 8 177 - 184 11 201 - 208 14 225 - 232
3 137 - 144 6 161 - 168 9 185 - 192 12 209 - 216 15 233 - 240
L OCATION 285 C ODE E NTRY L OGGING P ARTITION
(1 segment of numerical data) This location programs the partition that is logged with the Code Entry message and sent when the
following conditions are met:
 An RTE scan function is selected (Location 0, Segment 1/2/3, Option 8); and
 “RTE from a scanned card is to be logged as Code Entry” is enabled (Location 242, Segment 1, Option 5).
Entering a 0 (zero) will send the lowest valid partition of the reader. Entering 1-16 will send the entered value as the partition.
(Default is 0.)