GME GR9240W User Manual
Page 10
PA G E 1 0
i n s t r u c t i o n m A n uA l
G r 9 2 0 0 s E r i E s
PA G E 1 0
i n s t r u c t i o n m A n uA l
G r 9 2 0 0 s E r i E s
object (see PRECAUTIONS on page 5). This will ensure
the GR9200 is ready to operate for the first time. If at any
time the controls do not seem to work (after replacing the
vessel’s battery for example), press the Reset button to reset
the microcomputer inside the Gr9200 .
fuSE REplACEMENT
If any of the fuses blow, replace them with a standard
30 mm 3 AG type of the same rating. If the fuse blows a
second time contact your retailer.
the following fuse ratings are used:
- Yellow ‘Memory ’ lead: 15 Amp.
- red ‘ignition switch Acc’ lead: 0 .5 Amp .
OpERATION
GENERAl fuNCTIONS
1
power on/off
to turn the Gr9200 on, press the power Button . the unit
will resume the mode and settings that were selected when
last turned oFF .
to turn the Gr9200 off, press the power button again.
note that when the Gr9200 is turned oFF the clock is
displayed without the backlight.
Backlighting
Briefly press the Power button to change the brightness of
the back lighting. There are three levels of back
lighting available.
2
3
audio controls
The Volume, Bass, Treble, Balance and Fader controls are
selected electronically. The default setting is the
Volume control .
To select an alternative control, press the sel
3
button
until the desired function is displayed on the LCD. Each
press cycles to the next function in sequence. Adjust
the selected control function using the volume knob
2
.
4
loudness
Pressing the lou button will provide a low frequency (bass
lift) boost to the audio output. To indicate the selection
‘LOUD’ will be illuminated on the LCD. Pressing the lou
button again will de-select the loudness function.
5
mute
Pressing the mut button will temporarily silence the audio
output. ‘MUTE ON’ is displayed on the LCD to indicate the
GR9200 has been muted. Pressing the mut button again
will restore the previously selected audio level.
6
clock
To display the current time, press the button, After 2
seconds the display will return to it’s original status.
the time is shown in the 24 hour format .
To set the clock, press and hold the button until the
time display begins to flash. The time can then be adjusted
by rotating the Volume knob. To adjust hours, rotate the
knob clockwise, to adjust the minutes, rotate ant-clockwise.
7
mode
Pressing the mod button will select the GR9200 operating
mode. TUNER, CD or AUX modes are sequentially selected
as mod is pressed. If a USB memory stick or SD Card is
inserted, ‘USB’ or ‘CARD’ will also appear in the mode list.
When the Gr9200 is switched on it will automatically
return to the mode it was in when switched oFF .
8
local/distance control
Pressing the loc button selects an internal attenuator
which will help to reduce the interference and distortion
often associated with very strong local radio transmissions.
The LOC flag on the LCD is illuminated when the GR9200 is
in the local mode .
9
stereo/mono selector
Pressing the st button selects either mono or stereo
reception while in FM mode. The unit will momentarily
display ‘MONO’ or ‘STEREO’ when toggling the st switch .
The ST flag is displayed when the GR9200 is in the
stereo mode .
selecting mono improves reception when Fm signals are
weak or noisy by disabling stereo detection.
Select STEREO for normal listening on FM radio bands, a
symbol is displayed when stereo signals are
being received.
RAdIO OpERATION
country selection
When power is first applied, the GR9200 will default to the
European frequency bands. To toggle between European
and USA band sets:
1. Press and hold the memory ‘3’ key AND press the
power key.
2. The radio will display ‘Goodbye’ and switch off.
3. Switch the radio ON again using the power key. USA
or Europe will be momentarily displayed to indicate the
selected band.