Clarion VRX653R - Manual (Page 15)

VRX653R
17
English
Owner
’s manual
Basic Operations
When the panel is closed:
Each time you press the Z-EHCR button 9,
the tone effect changes in the following order:
“Z-EHCR 1”
➜ “Z-EHCR 2” ➜ “Z-EHCR 3” ➜
“Z-EHCR OFF”
➜ “Z-EHCR 1”...
When the panel is open:
1. Press the A-M button & to change into the
AUDIO-MODE display.
2. Operate the JOYSTICK ¡ upward or
downward to select “Z-EHCR”. Press the
ENT at the center of the JOYSTICK ¡ to
change into the Z-enhancer selecting
display.
3. Operate the JOYSTICK ¡ upward or
downward to select out of:
“TYPE 1” (Z-Enhancer 1) “TYPE 2” (Z-
Enhancer 2) “TYPE 3” (Z-Enhancer 3)
“OFF” (Z-Enhancer off),
and press the ENT at the center of the
JOYSTICK ¡ to set a desired Z-enhancer.
4. When the setting is finished, operate the
JOYSTICK ¡ rightward or leftward to move
the cursor to the “MENU”. Then press the
ENT at the center of the JOYSTICK ¡ to
return to the AUDIO-MODE display.
∗ To return from the AUDIO-MODE display to
the STANDARD display, press the A-M
button & once again.
Adjusting the Z-enhancer
Note:
• This function is enabled only when the panel is
open.
1. Press the A-M button & to change into the
AUDIO-MODE display.
2. Operate the JOYSTICK ¡ upward or
downward to select “Z-EH LVL” level. Press
the ENT at the center of the JOYSTICK ¡ to
change into the Z-enhancer adjusting display.
3. Operate the JOYSTICK ¡ upward or
downward to adjust the Z-enhancer level.
∗ When Z-Enhancer 1 is selected, you can
adjust the bass in the range of ±2.
∗ When Z-Enhancer 2 is selected, you can
adjust the treble in the range of ±2.
∗ When Z-Enhancer 3 is selected, you can
adjust the bass and treble in the range of ±2.
4. When the adjustment is finished, operate
the JOYSTICK ¡ rightward or leftward to
move the cursor to “MENU”. Then press the
ENT at the center of the JOYSTICK ¡ to
return to the AUDIO-MODE display.
Adjusting the bass and treble
Notes:
• This function is enabled only when the panel is
open.
• This function can be adjusted only when the Z-
enhancer is OFF.
1. Press the A-M button & to change into the
AUDIO-MODE display.
2. Operate the JOYSTICK ¡ upward or
downward to select “BAS/TRE”. Then press
the ENT at the center of the JOYSTICK ¡
to change into the BASS/TREBLE adjusting
display.
3. Operate the JOYSTICK ¡ rightward or
leftward to adjust the “BASS” or “TREBLE”.
4. Operate the JOYSTICK ¡ upward or
downward to adjust a level (adjustment
range: from -6 to 6).
5. When the adjustment is finished, operate
the JOYSTICK ¡ rightward or leftward to
move the cursor to “MENU”. Then press the
ENT at the center of the JOYSTICK ¡ to
return to the AUDIO-MODE display.
Adjusting the balance and fader
Note:
• This function is enabled only when the panel is
open.
1. Press the A-M button & to change into the
AUDIO-MODE display.
2. Operate the JOYSTICK ¡ upward or
downward to select “BAL/FAD”. Then press
the ENT at the center of the JOYSTICK ¡
to change into the BAL/FAD adjusting
display.
3. Operate the JOYSTICK ¡ rightward or
leftward to select “BALANCE” or “FADER”.
4. Operate the JOYSTICK ¡ upward or
downward to make an adjustment.
Adjusting range of the balance: L13 to R13
Adjusting range of the fader: front 12 / rear
12
5. When the adjustment is finished, operate
the JOYSTICK ¡ rightward or leftward to
move the cursor to “MENU”. Then press the
ENT at the center of the JOYSTICK ¡ to
return to the AUDIO-MODE display.