Crosman Z77 - Manual

Model Z77
Airsoft Gun 6mm Plastic BB
OWNER’S MANUAL
READ ALL INSTRUCTIONS AND WARNINGS IN THIS
MANUAL BEFORE USING THIS AIRSOFT GUN
Distributed by
Crosman Corporation
7629 Routes 5 & 20
Bloomfield, NY 14469
United States of America
www.crosman.com
Made in the U.S.A. with some foreign components Z77-515
This is not a toy. Adult supervision is required. Misuse may cause serious injury, particu-
larly to the eye. Eye protection must be worn by the user and any person in range. May be dangerous up to
100 yds. Read the owner’s manual before using.
Do not brandish or display this airsoft gun in public – it may confuse people and may be a
crime. Police and others may think it is a firearm. Do not change the coloration and markings to make it look
more like a firearm. That is dangerous and may be a crime.
This product contains a chemical known to the state of California to cause cancer and
birth defects (and other reproductive harms).
YOU AND OTHERS WITH YOU SHOULD ALWAYS WEAR SHOOTING GLASSES TO PROTECT YOUR EYES.
READ ALL INSTRUCTIONS BEFORE USING.
THIS AIRSOFT GUN IS INTENDED FOR USE BY THOSE 16 YEARS OF AGE OR OLDER.
BUYER AND USER HAVE THE DUTY TO OBEYALL LAWS ABOUT THE USE AND
OWNERSHIP OF THIS AIRSOFT GUN.
NOTE: Charge the battery a MINIMUM of 4 hours and a MAXIMUM of 5 hours prior to initial use. This airsoft
gun will not operate properly without a fully charged battery. DO NOT OVERCHARGE THE BATTERY. UNPLUG
THE BATTERY CHARGER WHEN NOT IN USE. USE ONLY THE CHARGER SUPPLIED WITH THE KIT. FOR
BEST RESULTS, FULLY CHARGE AND DISCHARGE THE BATTERY A MINIMUM OF 3 TO 5 TIMES.
Please read this owner’s manual completely. Remember to treat this airsoft gun with the same respect you would a
firearm. Always carefully follow the safety instructions found in this owner’s manual and keep this manual in a safe
place for future use.
If you have any questions regarding your new airsoft gun, please contact Crosman Customer Service at: 1-800-
724-7486, 585-657-6161 or www.crosman.com.
1. Learning the Parts of Your New Airsoft Gun
Learning the names of the parts of your new airsoft gun will help you to understand your owner’s manual. Use
thismanual to increase your enjoyment of this airsoft gun.
Fig. 1
A. Stock
B. Muzzle
C. Safety
D. Battery
E. Trigger
F. Magazine/Battery release (Fig. 4)
G. Trigger Guard
H. Hopper Optic
I. Hopper Load Port
2. Operating the Safety
Keep the airsoft gun in the “ON SAFE” position until you are actually ready to shoot. Then
push the safety to the “OFF SAFE” position.
Keep the airsoft gun in the “ON SAFE” position until you are actually ready to shoot. Then turn the safety to the
“OFF SAFE” position.
A. To Put the Airsoft Gun “ON SAFE”
• Locate the safety on left side of the receiver (Fig. 2).
• Rotate lever so that the lever is lined up with the word “SAFE”.
B. To Take the Airsoft Gun “OFF SAFE”
NOTE: This airsoft gun fires in full-auto mode. Full-auto means it will continue to fire
plastic BBs as long as you hold the trigger.
• Locate the safety on left side of the receiver (Fig. 2).
• Rotate the lever to the full fire position.
• The airsoft gun is “OFF SAFE” and ready to fire when safety is pointing to “Full”
Position.
Like all mechanical devices, an airsoft gun safety can fail. Even when the safety is
“ON SAFE”, you should continue to handle the airsoft gun safely. NEVER point the
airsoft gun at any person. NEVER point the airsoft gun at anything you do not intend to shoot.
3. Adjusting the Size of Your Airsoft Gun
A. Installing and Removing the Stock
• To install, line stock up with grooves at the back of the rifle. With the stock in this position push the stock down
until it locks into place.
• To remove the stock, pull the stock release button toward the back of the stock. Push the stock upward until it
has cleared the rail.
NOTE: For optimum performance Crosman recommends using only Crosman brand airsoft BBs.
4. Loading and Unloading
Use 6 mm plastic BBs only in this airsoft gun. Use of any other ammunition can cause
injury to you or damage to the airsoft gun.
A. Installing and Filling the Hopper-Loading Chamber.
• Make sure the airsoft gun is “ON SAFE” (section 2A) and
pointed in a SAFE DIRECTION.
• Make sure your loading chamber is empty.
• Loosen the mounting screws on the loading chamber.
• With the small end toward the rear of the gun, place the
loading chamber on the top rail, lining up the hole & arrows
on the gun with the hole on the loader (Fig.3).
• Tighten the mounting screws.
• Slide open the loading chamber door located on top of the
chamber.
• Fill the chamber with 6mm BBs and slide the door closed.
Use 6 mm plastic BBs only in this airsoft gun. Use of any other
ammunition can cause injury to you or damage to the airsoft
gun.
Never assume that because the airsoft gun no longer fires a plastic BB and/or the maga-
zine is removed, that a plastic BB is not lodged in the barrel. Always treat the airsoft gun as though it is
loaded and with the same respect you would a firearm.
B. Unloading Plastic BBs
• Make sure the airsoft gun is “ON SAFE” (section 2A).
• Point the airsoft gun in a SAFE DIRECTION.
• To empty the chamber slide open the door on the top of the chamber and pour the BBs out into a container or
your hand.
• Point the airsoft gun in a SAFE DIRECTION, take “OFF SAFE” and fire the gun in a safe direction until no more
BBs fire.
• Put the airsoft gun back “ON SAFE”.
Never assume that because the airsoft gun no longer fires a BB and/or the loading chamber is removed, that a BB
is not lodged in the barrel. Always treat the airsoft gun as though it is loaded and with the same respect you would
a firearm.
5. Charging, Loading and Removing the Battery
A. Charging the Battery
NOTE: Charge the battery a MINIMUM of 4 hours and a
MAXIMUM of 5 hours prior to initial use. This airsoft gun will not
operate properly without a fully charged battery.
DO NOT OVERCHARGE THE BATTERY. UNPLUG THE BAT-
TERY CHARGER WHEN NOT IN USE. USE ONLY THE CHAR-
GER SUPPLIED WITH THE KIT.
• Remove the battery from the airsoft gun (see section 5C).
• Plug the charger into the bottom of the battery.
• Plug the charger into a standard 110v outlet.
• Charge for no more than 5 hours and unplug charger from
outlet.
• Disconnect the battery from the charger.
B. Loading the Battery
• Make sure the airsoft gun is “ON SAFE” (section 2A) and is
UNLOADED.
• Point the airsoft gun in a SAFE DIRECTION.
• Insert the battery into the gun so that the metal connectors (positive end) are on top and lock battery in place
(Fig. 4A).
C. Removing the Battery
• Make sure the airsoft gun is “ON SAFE” (section 2A) and is UNLOADED.
• Point the airsoft gun in a SAFE DIRECTION.
• While holding the airsoft gun in a horizontal position press the battery release lever forward with one hand, and
pull the battery out with the other hand (Fig. 4B).
NOTE: This airsoft gun fires in full-auto mode. Full-auto means it will continue to fire plastic BBs as long as
you hold the trigger.
Fig. 2
Fig. 3
Fig. 4
Fig. 4B
• You and others with you should always wear eye protection
designed for airsoft to protect your eyes.
• Always point your airsoft gun in a SAFE DIRECTION.
Do not shoot at hard surfaces or at the surface of water. The
plastic BBs may bounce off or ricochet and hit someone or
something you had not intended to hit.
• DO NOT re-use plastic BBs because they could damage
your airsoft gun.
• Your airsoft gun is designed for target shooting and is suited
for both indoor and outdoor use. Always remember to place
your target carefully. THINK about what you will hit if you
miss the target.
• When you are sure of your target and backstop, and the
area around the target is clear, load and charge the airsoft
gun following sections 3 and 4. Take the airsoft gun “OFF
SAFE” (section 2A) aim and pull the trigger to fire.
7. Maintaining Your Airsoft Gun
• DO NOT MODIFY OR ALTER YOUR AIRSOFT GUN. Attempts to modify the airsoft gun in any way inconsistent
with this manual may make it unsafe to use, cause serious injury and will void the warranty.
• If you drop your airsoft gun, check to see that it works properly before you use it again. If anything seems
changed, like a shorter or weaker trigger pull, this may mean worn or broken parts. Call Customer Service at
Crosman for assistance before using your airsoft gun again.
A. To clean the Airsoft gun barrel:
• Spray a cleaning patch with Crosman Nitro Lubricant oil.
• With patch on rod, insert in into barrel to clean
• Swab barrel 3-4 times
• Repeat swabbing procedure with a dry patch
• Barrel is clean when patches come out clean after dry swabbing.
B. Trouble shooting/Increasing Your Shooting Enjoyment
• Occasionally shake the gun to ensure smooth BB feeding.
• Prevent dust and dirt from getting into the magazine to help maintain the performance of your airsoft rifle.
• Change the battery if firing cycle becomes slow.
C. Clearing a Jam
• Never look down the end of barrel to see if a jam has been cleared.
• Make sure the airsoft gun is “ON SAFE” and pointed in a SAFE DIRECTION.
• Remove the loading chamber
• Insert the tapered end of the cleaning rod into the barrel, with the angle toward the breech (where the magazine
connects).
• CAREFULLY and slowly apply more pressure until you push the BB out of the breech.
• Reinstall the magazine and test gun.
8. Reviewing Safety
• Do not ever point the airsoft gun at any person. Do not ever point the airsoft gun at anything you do not intend
to shoot.
• Always treat the airsoft gun as though it is loaded and with the same respect you would a firearm.
• Always aim in a SAFE DIRECTION. Always keep the muzzle of the airsoft gun pointed in a SAFE DIRECTION.
• Always keep the airsoft gun “ON SAFE” until you are ready to shoot in a SAFE DIRECTION.
• Always check to see if the airsoft gun is “ON SAFE” and unloaded when getting it from another person or from
storage.
• Always keep your finger off the trigger and out of the trigger guard until ready to shoot.
• You and others with you should always wear eye protection to protect your eyes.
• Always wear eye protection designed for airsoft over your regular glasses.
• Use 6 mm plastic BBs only.
• Do not reuse plastic BBs because they could cause possible damage to your airsoft gun.
• Do not shoot at hard surfaces or at the surface of water. The plastic BBs may bounce off or ricochet and hit
someone or something you had not intended to hit.
• Replace the backstop if it becomes worn. Place the backstop in a location that will be safe should the back-
stop fail.
• Your backstop should be checked for wear before and after each use. All backstops are subject to wear and
will eventually fail. Replace your backstop if the surface is worn or damaged or if a ricochet occurs.
• Do not attempt to disassemble or tamper with your airsoft gun.
• DO NOT MODIFY OR ALTER YOUR AIRSOFT GUN. Attempts to modify the airsoft gun in any way may make
your airsoft gun unsafe to use, cause serious injury or death and will void the warranty.
• Using unauthorized repair centers or modifying the function of your airsoft gun in any way may be unsafe and
will void your warranty.
• Do not put the airsoft gun away loaded. Make sure ALL of the plastic BBs are unloaded from the airsoft gun.
• Always store this airsoft gun in a secure location.
SPECIFICATIONS
Mechanism Action Electronic
Caliber Ammunition 6mm plastic BBs
Reservoir Up to 500 6mm BBs
Safety Lever
Velocity Up to 200 fps
DO NOT RETURN THIS PRODUCT TO THE STORE.
Our friendly customer service representatives will be glad to help. You can get answers to frequently asked ques-
tions at www.crosman.com or you can contact us directly at 1-800-724-7486.
CUSTOMER SERVICE
If your airsoft gun is not functioning, we recommend that you call Crosman Corporation Customer service at 1-800-724-
7486 or 585-657-6161. (International customers should contact their distributor.) DO NOT ATTEMPT TO DISASSEMBLE
IT! If you take it apart you probably will not be able to reassemble it correctly. Crosman assumes no warranty responsibil-
ity under such circumstances.
For optimum performance use Crosman ammunition only. Using other than Crosman branded ammunition may cause
your product to malfunction and may void your warranty.
LIMITED 30 DAY WARRANTY
This product is warranted to the retail consumer for 30 days from date of retail purchase against defects in material and
workmanship and is transferable.
WHAT IS COVERED
Replacement parts and labor. Transportation charges to consumer for repaired product.
WHAT IS NOT COVERED
Transportation charges to Crosman for product. Damages caused by abuse, modification or failure to perform normal
maintenance. Any other expense. CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, OR INCIDENTAL EX-
PENSES, INCLUDING DAMAGE TO PROPERTY. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION
OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY
TO YOU.
WARRANTY CLAIMS
USA Customers: Attach your name, address, description of problem, phone number and copy of sales receipt to
product. Package and return to Crosman Corporation, Routes 5 & 20, Bloomfield, NY 14469.
Canadian Customers: Contact the Gravel Agency 418-682-3000 X46.
International Customers: Please return product to your nearest distributor. If you do not know your distributor, please
call 585-657-6161 and ask for our International Department for assistance.
IMPLIED WARRANTIES
ANY IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO 30 DAYS FROM DATE OF RETAIL PURCHASE. SOME
STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITA-
TIONS MAY NOT APPLY TO YOU.
To the extent any provision of this warranty is prohibited by federal, state, or municipal law which cannot be preempted, it
shall not be applicable. This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
CROSMAN is a registered trademark of Crosman Corporation in the United States.