Crosman 30021 - Manual

Model Crosman ® Vantage NP
.177 cal Air Rifle
OWNER’S MANUAL
READ ALL INSTRUCTIONS AND WARNINGS IN THIS MANUAL BEFORE USING THIS AIRGUN
Crosman Corporation
7629 Rts. 5 & 20
Bloomfield, NY 14469
United States of America
800-7-AIRGUN
www.crosman.com
Made in China 30020-515
Not a toy. This airgun is recommended for adult use only. Misuse or careless use may
cause serious injury or death. May be dangerous up to 600 yards (594 m).
Do not brandish or display this airgun in public—it may confuse people and may be a
crime. Police and others may think it is a firearm. Do not change the coloration and markings to make it look
more like a firearm. That is dangerous and may be a crime.
YOU AND OTHERS WITH YOU SHOULD ALWAYS WEAR SHOOTING GLASSES TO PROTECT YOUR EYES.
READ ALL INSTRUCTIONS BEFORE USING.
BUYER AND USER HAVE THE DUTY TO OBEY ALL LAWS
ABOUT THE USE AND OWNERSHIP OF THIS AIRGUN.
THIS AIRGUN IS INTENDED FOR USE BY ADULTS ONLY
This product contains one or more chemicals known to the state of California to cause
cancer and birth defects or other reproductive harm. Wash hands after handling.
This airgun has been classified as an adult gun, and is recommended for adult use only.
Because it is considered to be a special-purpose airgun, it is exempt from specific types of trigger pull,
safety mechanisms and drop tests.
Read this owner’s manual completely. And remember that an airgun is not a toy. Always carefully follow the safety
instructions in this owner’s manual and keep the manual in a safe place for future use. If you have any questions
regarding the operation of your new airgun contact Crosman at 1-800-724-7486.
1. Learning the Parts of Your New Airgun.
Learning the parts of your new airgun helps you understand your owner’s manual. Use this manual to increase your
enjoyment of this airgun.
Break in Period
There may be up to a 100
shot break-in period. During
this period accuracy may be
inconsistent and your gun
may seem loud. This will
improve as the nitro piston
breaks in.
2. Operating the Safety
A. To Put the Airgun “ON SAFE:”
• Locate the safety in front of the trigger.
• The letters “F” (fire) and “S” (safe) on the bottom of the trigger guard indicate the appropriate position of the safety.
• Push the safety towards the trigger to put the safety on. The safety is on, and the airgun is “ON SAFE” when
the lever is in the rear position (near the trigger). (Fig. 2)
Even when the safety is on, you should continue to handle the airgun safely. Don’t point the gun at anything you
don’t intend to shoot.
Like all mechanical devices, an airgun safety can fail. Even when the safety is “ON SAFE”, you should continue to
handle the airgun safely. NEVER point the airgun at any person. NEVER point the airgun at anything you do not
intend to shoot.
B. To Take the Airgun “OFF SAFE”
Keep the airgun “ON SAFE” until you are actually ready to shoot. Then push the safety to the
“OFF SAFE” position.
• Push the safety to the forward position (away from the trigger). When the airgun is “OFF SAFE” (Fig. 2) it is
ready to be fired after following the instructions in this manual on how to load.
3. Adjusting the Trigger
This airgun has a trigger with a screw for adjustment of the second
stage length (Fig. 3)
Note: This feature is added for advanced shooters. Most shooters
can use the settings provided during manufacturing of the gun and
should not need to make any modifications.
• Make sure airgun is “ON SAFE”, unloaded and not cocked.
• To reduce the second stage length, rotate the adjusting screw
counterclockwise.
• To increase the second stage length, rotate the adjusting screw
clockwise.
4. Cocking and Loading Your Airgun
•
A. Cocking Your Airgun
Make sure you do not touch the trigger or push the safety to the “OFF SAFE” position.
Do not cock your airgun until you are ready to load and fire, since the only way to un-cock your airgun is to fire it.
Firing your gun without a pellet in the chamber (dry firing) may cause damage to your airgun.
• Put the airgun “ON SAFE” (SECTION 2).
• Point the airgun in a SAFE DIRECTION.
• Holding the gun close to your body, firmly tap the muzzle. (Fig. 4A)
• Anchor gun against thigh and pull barrel down as far as it will go to engage the nitro piston. (Fig.4B)
• Be careful not to pinch your hand or fingers in the hinge area of the airgun.
B. Loading Your Airgun
Make sure you do not pull the trigger while cocking the air rifle or with the barrel in the
down position. This may cause serious damage to the air rifle.
CAUTION: Use .177 caliber pellets only in your Vantage NP. Never reuse ammunition. Your air gun was designed
to work with Crosman branded ammunition, these include Crosman ® and Benjamin. Use of any other ammunition
can cause injury to you or damage to the airgun.
There may be up to a 100 shot break-in period. During this period accuracy may be inconsistent and your gun may
seem loud. This will improve as the nitro piston breaks in.
• With the barrel in the open position, after it has been cocked, place one pellet, nose forward, into the breech
(Fig. 5). Make sure that the skirt of the pellet is flush with face of breech.
• Move the barrel back to its original position by pushing the barrel up until it locks (Fig. 6).
• Be sure that the barrel is locked in the closed position after loading/cocking to help ensure better accuracy.
•
Once again, be careful not to pinch your hands or fingers. Be sure the airgun is “ON SAFE” and pointed in a safe
direction.
Your air rifle is now loaded and ready to fire. Keep the air rifle “ON SAFE” until you are
ready to shoot. Do not point at anything you don’t intend to shoot.
C. Unloading Your Airgun
Do not cock and load your airgun until you are ready to shoot since the only way to un-cock your airgun is to fire it
in a safe direction. REMEMBER, choose your targets carefully and be sure that the area around the target is clear.
THINK what you will hit if you miss the target! Do not store your gun cocked or loaded.
5. Aiming and Firing Safely
A. Aiming and Firing the Airgun
• You and others with you should always wear shooting glasses to protect your eyes.
• Always aim your airgun in a SAFE DIRECTION.
• Do not shoot at hard surfaces or at the surface of water. The pellet may bounce off or ricochet and hit some-
one or something you had not intended to hit.
• Always choose your target carefully. It is best to shoot at paper bull’s-eye targets which are attached to a safe back-
stop. A heavy blanket should be hung behind the backstop to prevent ricochet should you miss the backstop.
• Your backstop should be checked for wear before and after each use. Replace your backstop if the surface is
worn or damaged or if a ricochet occurs.
• Your airgun is designed for target shooting. Always remember to place your target carefully.
• THINK about what you will hit if you miss the target.
• When you are sure of your target and backstop, and the area around the target is clear, take the airgun “Off
Safe” (see Section 2.2) and pull the trigger to fire.
6. Removing a Jammed Pellet
• Put your airgun “ON SAFE” (Section 2A).
• Do not reload the airgun if a pellet is jammed.
• Break the barrel open slightly (without pulling the barrel all the way down to the point that it cocks the action)
and look down the breech to see if the gun is jammed.
• If it is jammed, insert a cleaning rod into the breech and push the jammed pellet out of the muzzle. Don’t try to
reuse that pellet (Fig. 7)
Do not cock the airgun during the removal of a jammed pellet unless you plan on continu-
ing to shoot.
Remember: do not fire your airgun without a pellet in the chamber (dry fire). This may permanently damage your
airgun.
• If you are not able to unjam your airgun by following the unloading procedure, take no further action. An Autho-
rized Service Station will unjam your airgun (no cost during the warranty
period).
7. Maintaining Your Airgun
• Periodically tighten all stock fasteners
• Check and tighten scope mounts if applicable
• To ensure that your air rifle maintains uniform power, it is important that
you apply a drop of Crosman RMCOIL every few hundred shots into the
compression chamber. (Fig. 8) The external metal parts should be cleaned
with a cloth that has RMCOIL on it.
CAUTION: Use Crosman RMCOIL only and do not over-oil. To do so can
cause possible damage to the gun and injury to the shooter and bystanders.
CAUTION: Do not attempt to disassemble your airgun. DO NOT MODIFY OR
ALTER YOUR AIRGUN. Attempts to modify the airgun in any way inconsistent
with this manual may make your airgun unsafe to use, cause serious injury or
death, and will void the warranty.
If you drop your airgun, visually check to see that it works properly before you
use it again. If anything seems changed, like a shorter or weaker trigger pull, this may mean worn out or broken
parts. Call Crosman customer service for assistance before using your airgun again.
8. Reviewing Safety
• Never point the airgun at any person or at anything you do not intend to shoot.
• Always treat the airgun as though it is loaded and with the same respect you would a firearm.
• Always aim in a SAFE DIRECTION. Always keep the muzzle of the airgun pointed in a SAFE DIRECTION.
• Always keep the airgun on safe until you are ready to shoot.
• Always check to see if the airgun is “ON SAFE” (see section 2A) and unloaded when getting it from another
person or from storage.
• Always keep your finger off the trigger and out of the trigger guard until ready to shoot.
• You and others with you should always wear shooting glasses to protect your eyes.
• If your reading or prescription glasses are not safety glasses, make sure you wear shooting glasses over your
regular glasses.
• Use .177 caliber (4.5mm) pellet only in your Vantage NP. NEVER reuse ammunition.
• Do not shoot at hard surfaces or at the surface of water. The pellet may bounce off or ricochet and hit some-
one or something you had not intended to hit.
• Place the backstop in a location that will be safe should the backstop fail.
• Your backstop should be checked for wear before and after each use. All backstops are subject to wear and
will eventually fail. Replace your backstop if the surface is worn or damaged or if a ricochet occurs.
• Do not attempt to disassemble or tamper with your airgun. Use an Authorized Service Station. Using unauthor-
ized repair centers or modifying the function of your airgun in any way may be unsafe and will void your warranty.
• Before you store your airgun make sure it is not loaded or cocked.
• Whenever you store the airgun, make sure it is “ON SAFE” (see section 2A.)
SPECIFICATIONS
Mechanism Break Barrel Length 45”
Power source Nitro Piston Velocity
• Up to 1200fps with high velocity pellet
• Up to 1000fps with standard pellet.
Caliber/ammunition .177 cal pellet Safety Ambidextrous Lever
Weight 7.1 lbs
PERFORMANCE
Many factors can affect velocity, including brand of projectile and weight of projectile.
Your air gun was designed to work with Crosman branded ammunition, these include Crosman
® and Benjamin ® . Use of
other ammunition may cause your gun to malfunction.
Break in Period
There may be up to a 100 shot break-in period. During this period accuracy may be inconsistent and your gun may seem
loud. This will improve as the nitro piston breaks in.
DO NOT RETURN THIS PRODUCT TO THE STORE.
Our friendly customer service representatives will be glad to help. You can get answers to frequently asked questions at
www.crosman.com or you can contact us directly at 1-800-7AIRGUN (1-800-724-7486)
REPAIR SERVICE
If your airgun needs repair, we recommend you take or send it to your nearest Crosman Authorized Service Station. DO
NOT ATTEMPT TO DISASSEMBLE IT! Your airgun requires special tools and fixtures to repair it. Any disassembly or modifi-
cation not performed by an Authorized Service Station will void the warranty.
A SPECIAL CUSTOMER SERVICE
Crosman Authorized Service Stations will unjam your airgun at no cost during the warranty period.
LIMITED ONE YEAR WARRANTY
This product is warranted to the retail consumer for one year from date of retail purchase against defects in material and
workmanship and is transferable. To register the serial number of your airgun return the airgun registration form. The war-
ranty is not conditioned on the return of the card. You should retain the original sales receipt as record of date of purchase.
WHAT IS COVERED
Replacement parts and labor. Transportation charges to consumer for repaired product.
WHAT IS NOT COVERED
Transportation charges to Authorized Service Station for defective product. Damages caused by abuse, modification or fail-
ure to perform normal maintenance – see Owner’s Manual. Any other expense. CONSEQUENTIAL DAMAGES, INCIDEN-
TAL DAMAGES, OR INCIDENTAL EXPENSES INCLUDING DAMAGE TO PROPERTY. SOME STATES DO NOT ALLOW
THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR
EXCLUSION MAY NOT APPLY TO YOU.
HOW TO OBTAIN WARRANTY PERFORMANCE
U.S. Customers- Locate nearest service station (see www.crosman.com or call Crosman customer service at 800-724-
7486 for list of stations). The service station will give you details of how to proceed with sending the item in for repair. You
must contact the station before shipping your product.
International Customers- Return product to your nearest distributor. If you do not know your distributor call 585-657-
6161 and ask for our International Department for assistance.
IMPLIED WARRANTIES
ANY IMPLIED WARRANTIES INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE ARE LIMITED IN DURATION TO ONE YEAR FROM DATE OF RETAIL PURCHASE. SOME
STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS SO THE ABOVE LIMITATIONS
MAY NOT APPLY TO YOU.
To the extent any provision of this warranty is prohibited by federal, state or municipal law, which cannot be preempted, it
shall not be applicable. This warranty gives you specific legal rights and you may also have other rights, which vary, from
state to state.
CROSMAN is a registered trademark of Crosman Corporation in the United States.