Key features, High speed processing, Advanced instruction set – Toshiba T2E User Manual
Page 3: Two programming languages, Built-in clock/calendar, Password protection, Battery-fess operation ft2e), Ethernet connection (t2n, High speed industrial lan, Device net
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".

Key Features
High speed processing
The Т2ЕЯ2Ы excels at applicartions where high speed
processing is required.
• 0.33 ps/contact
• 0.44 ps/coii
• 1.2 ps/16*bit transfer
• 1.63 ps/16*bit addition
Advanced instruction set
The T2E/T2N offers 24 basic relay-ladder instructions
and 192 function block instructions, including the
following.
• Arithmetic operation • Data manipulations
• Trigonometric functions • PID/ramp/intsgral
• Subroutine call
• For-Next loop
• Averaging/filteiing • ASCII ** Hex conversion
• Floating-point math
Two programming Languages
The T2E/T2N supports two programming languages:
Ladder Diagram {LD) and Sequential Function Chart
(SFC). By selecting the appropriate language, or
coinbination of the two, program developrrtent time
can be greatly reduced.
Built-in clock/calendar
TheT2E/T2N has a real-time-clock/catendar function
(year, month, day, week, hours, minutes, seconds)
that can be used for performing scheduled
operations, data gathering with time stamps, etc,
Password protection
The T2E/T2N can be programmed with one of four
selectable protection levels.
• Level 1: No protect (normal)
• Level 2: Wrlting/moditying program prohibited
• Level 3: Level 2 plus viewing program prohibited
• Level 4: Level 3 plus writing data prohibited
Battery-fess operation fT2E)
The user-program is saved in a built-in Flash
memory. No battery maintenance is required.
Ethernet connection (T2N|
The T2N CPU modules (PU235N and PU245N) have
built-in Ethernet interface (10BASE-T). Through the
Ethernet, the T2N can communicate with higher level
controllers (computer, workstation, etc.) or other
PLCs with Ethernet.
High speed industrial LAN
The T2E/T2N can be connected to Toshiba’s high
speed industrial LANs (Local Area Networks)
TOSLINE-S20 and TOSLINE-FIO. Tbe TOSLINE
series are suited for real-time control data linkage.
Through these networks, the T2E/T2N can exchange
data with other Toshiba equipment, such as the
TOSDiC CIE system, other T-sehes PLCs, Large
Adjustable Speed Drives, General Purpose Inverters,
etc.
The T2N CPU module PU245N has the TOSUNE-
S20LP (Loop version) built-in into the CPU module.
The TOSLINE-S20LP is a high-ral¡ability double-loop
fiber optic S20 rtetwork.
Device Net
A DeviceNat scanner module Is avalable for the
T2E/T2M. The DeviceNet scanner module can
read/write data to any other manufacturer's ODVA
certified devices (I/O blocks. Inverters to include
Toshiba’s G3, air valve manifolds, sensors, etc.).
Flexible serial port
The T2En-2N has RS-232C or RS-485 serial
communication port, (It is optional in the T2E)
Using this port, one of the following communication
modes can be selected.
• Computer link mode: Connection with higher level
computer, MMl/SCADA system, modem, etc.
• Data link mode: Easy data linkage between two
T2Es, T2Ns, T2E—T2N or T2E/T2N—Super T1.
• Free ASCII mode: Active communication between
serial ASCII devices, (bar code readers, etc.)
Programmer port function
The T2E/T2N*s RS-232G programmer port supports
the T-series computer link protocol. This allows easy
connection to a higher level computer, an operator
interface unit, a modem, etc.