Casio 4343 - Manual (Page 7)

Operation Guide 4343
7
If the time setting of your watch is not correct even though time calibration signal reception is being performed normally, use the
procedure in this section to check the home positions of the hands and make adjustments as required. Note that you do not need to
perform the following operation if your watch is showing the correct time.
2.
Use the B B B B B button to
adjust the position
of the indicator hand
and the C
C C C C button to
adjust the position
of the second hand.
• The hands move
clockwise only. Keep
pressing the buttons
until the applicable
hand is at its proper
home position.
30
1.
In the Timekeeping Mode,
hold down the A
A A A A button
and then the C C C C C button for
about five seconds.
• The watch will beep, and then
the indicator hand and the
second hand will move their
home positions.
Home Position
Indicator Hand: 12 o’clock
Second Hand: 0
• If the indicator hand and second hand are both at their
proper home positions, advance to step 3.
Home Position Adjustment
4.
Use the D D D D D (+) and
B B B B B (–) buttons to
adjust the hands.
• Holding down either button will cause the hands to
move at high speed. Once started, high-speed hand
movement will continue even if you release the button.
To stop high-speed hand movement, press any button.
• The 24-hour hand is synchronized with the hour and
minute hands, so separate adjustment is not required.
5.
Press the C C C C C button.
• This will cause the
chronograph hour and minute
hands to move to their home
positions.
Home Position
Hour Hand: 24:00
Minute Hand: 24:00
• If the hour and minute hands are at their proper home
positions, advance to step 7.
If the chronograph hour and minute hands
are not at their proper home positions
30
30
Chronograph Hands
30
7.
Check the day indicator. If
it is not at its home
position, use the C
C C C C
button to move it there.
Home Position
Day 1
• If the Day is at its proper home position, advance to step 9.
If the Day is not at its proper home position
8.
Use the D D D D D (+) and
B B B B B (–) buttons to
adjust the day.
• Holding down either button will cause the day to change
at high speed. Once started, high-speed day change
will continue even if you release the button. To stop
high-speed day change, press any button.
9.
Press the A A A A A button to exit
home position adjustment
and return to the
Timekeeping Mode.
• If you press the C button
instead of the A button in
step 1, the watch will return to
step 1 (indicator hand and
second hand home position
adjustment) of this procedure.
• The watch also will exit home
position adjustment
automatically if you do not
perform any operation for
about two or three minutes.
After completing the home position adjustment procedure, put
the watch in a location where it is able to receive the time
calibration signal easily and perform a manual receive
operation.
• For details about the manual receive procedure, see
“Receiving the Calibration Signal”.
1
Day
1
30
3.
Press the C C C C C button.
• This will cause the hour hand,
minute hand, and 24-hour
hand to move to their home
positions.
Home Position
Hour Hand: 12 o’clock
Minute Hand: 12 o’clock
24-hour Hand: 24:00
• If the hour, minute, and 24-hour hands are all at their proper
home positions, advance to step 5.
If the chronograph hour and minute hands
are not at their proper home positions
6.
Use the D D D D D (+) and
B B B B B (–) buttons to
adjust the hands.
• Holding down either button will cause the hands to
move at high speed. Once started, high-speed hand
movement will continue even if you release the button.
To stop high-speed hand movement, press any button.
30
Indicator Hand
Second Hand
30
Hour and Minute Hands
24-hour Hand
If the indicator hand or second hand is
not at its proper home position