Caterpillar TAURUS 70 User Manual

Page 9

Turbomachinery Package Specification

Taurus

70 Compressor Set and Mechanical Drive

Table 1.

Package Specifications

Dimensions

Approximate Package Measurements

Height, Unenclosed

3.27 m

(10 ft 9 in.)

Height, Enclosed

3.66 m

(12 ft 0 in.)

Width (to skid edges)

2.64 m

(8 ft 8 in.)

Width (including lifting bollards)

2.90 m

(9 ft 6 in.)

Length, Engine Skid

7.70 m

(25 ft 3 in.)

Approximate Package Weights

Gearbox (If Applicable)

1630 kg

(3,600 lb)

AC Start Motor Assembly

380 kg

(840 lb)

Pneumatic Start Assembly

259 kg

(570 lb)

Gas Turbine Assembly (SoLoNOx)

5630 kg

(11,260 lb)

Total Driver (unenclosed package, without oil)

24 494 kg

(54,000 lb)

Total Driver (enclosed package, with oil)

33 693 kg

(74,280 lb)

Piping and Tubing Thickness

Piping > 76.2 mm (3 in.) Nominal Pipe Size (NPS)

Schedule 40 (Unless Otherwise Specified)

Piping < 50.8 mm (2 in.) NPS

Schedule 80 (Unless Otherwise Specified)

Tubing 3.175 mm (0.125 in.) Nominal Tubing Size
(NTS)

0.889 mm (0.035 in.) Minimum Wall Thickness

Tubing 6.35 mm (0.25 in.) NTS

1.245 mm (0.049 in.) Minimum Wall Thickness

Tubing 12.7 mm (0.500 in.) NTS

1.651 mm (0.065 in.) Minimum Wall Thickness

Tubing 19.05 mm (0.75 in.) NTS

1.651 mm (0.065 in.) Minimum Wall Thickness

Tubing 25.40 mm (1.00 in.) NTS

2.108 mm (0.083 in.) Minimum Wall Thickness

Tubing 31.75 mm (1.25 in.) NTS

2.768 mm (0.109 in.) Minimum Wall Thickness

Construction Materials

Piping, Manifolds, and Tubing < 10.2 cm (4 in.)
Note (a)

316L Stainless Steel (Unless Otherwise Specified)

Piping, Manifolds, and Tubing > 10.2 cm (4 in.)
Note (a)

Carbon Steel (Unless Otherwise Specified)

Piping Interface Connections

316L Stainless Steel (Unless Otherwise Specified)

Flange Assembly Hardware

316L Stainless Steel

Pipe Support Brackets

Carbon Steel (Standard)
316L Stainless Steel (Optional)

Pipe Flexible Couplings

Carbon Steel (Standard)
316L Stainless Steel (Optional)

Tubing Dual Ferrule Compression Fittings

316L Stainless Steel

Sliding Lube Oil Drain Couplings and Plates

Carbon Steel (Standard)
316L Stainless Steel (Optional)

Lube Oil Vent Flame Arrestor

Carbon Steel (Standard)
316L Stainless Steel (Optional)

Electrical System Certifications

NEC

Class 1, Group D, Division 1 or 2

CENELEC

Zone 1 or 2, Group II

CE, ATEX

Zone 2, Group II

Three-Phase Package Motors

Optional Motor Voltage Ratings

380, 400, or 415 VAC, 50 Hz
460 VAC 60 Hz

Single-Phase Battery Charger

Optional Battery Charger Voltage Ratings

220, 230, 240, 380, 400, 415, 440, 460, or 480
VAC, 50 Hz or 60 Hz

TPS70CSMD/309