Setting warmer drawer controls (cont d), Warmer drawer recommended food settings table, To replace warmer drawer – Kenmore 790.9621 User Manual
Page 18: Setting warmer drawer controls, Cont d)
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
Setting Warmer Drawer Controls
(cont d)
Warmer Drawer Recommended
Food Settings Table
Food Item
Setting
Bacon
HI
Hamburger Patties
HI
Poultry
HI
Pork Chops
HI
Fried Foods
HI
Pizza
HI
Gravies
MED
Casseroles
MED
Eggs
MED
Roasts (Beef, Pork, Lamb)
MED
Vegetables
MED
Biscuits
MED
Rolls, hard
MED
Pastries
MED
Rolls (soft)
LO
Empty Dinner Plates
LO
Pull up with finger
To Set the Warmer (Warm & Ready™) Drawer Thermostat
Control (some models)
The thermostat control Is used to select the temperature of the warmer drawer.
It is located on the control panel (See Fig. 3 on previous page). To set the
thermostat, push in and turn the knob to the desired setting. The temperatures
are approximate, and are designated by HI, MED and LO.
1. Turn the knob to select the desired temperature setting,
2. For best results, preheat the drawer before adding food. An empty drawer
will preheat in approximately 15 minutes.
3. Turn the thermostat control to OFF after use.
Warmer (Warm & Ready™) Drawer Temperature Selection
(some models)
Refer to the table in the side column for recommended settings. If a particular
food is not listed, start with the medium setting. If more crispness is desired,
remove the lid oraluminumfoil.
Most foods can be kept at serving temperatures by using the medium setting.
When a combination of foods are to be kept warm (for instance, a meat with 2
vegetables and rolls), use the high setting.
Refrain from opening the warmer drawer while in use to eliminate loss of heat
from the drawer.
Warmer (Warm & Ready ™) Drawer Indicator Light (some models)
The indicator light is located above the Warmer Drawer thermostat control. It
turns on when the control is set, and stays on until the control is turned OFF.
The warmer drawer is inoperable during the Self-Clean cycle. The indicator light
will not come on during the Self-Clean cycle.
To Remove and Replace Warmer (Warm & Ready™) Drawer
(some models)
To Remove Warmer Drawer:
iOl^CAUTION
Turn power OFF before removing the warmer drawer.
2. Open the drawer to the fully opened position.
3. On the right glide you will find a shield attached with a hex-head screw (see
figure 1). Using a 1/4” socket and ratchet remove the shield.
4.
Locateglideleveroneachsideofdrawer, pull upontheleftglideleverand push
down on the right glide lever.
5. Pull the drawer away from the range.
To Replace Warmer Drawer:
1. Replace shield on the right glide of the drawer body.
2. Puli the bearing glides to the front of the chassis glide (see figure 2).
3. Align the glide on each side of the drawer with the glide slots on the range.
4. Push the drawer into the range until levers “click” (approximately 2”). Pull the
draweropen again to seat bearing glides into position. If you do not hear the
levers “click” or the bearing glides do not feel seated remove the
drawer and repeat steps 2-4. This will minimize possible damage to the
bearing glides.
NOTE: The warmer drawer wilt NOT
operate while in the Self-Clean and 'Oven
Lockout” modes
........
WARNING
Electrical Shock Hazard can occur and result in
serious injury or death. Disconnect appliance from electric power
before cleaning and servicing the warmer drawer.
18