Warning electrical shock hazard, Warning – Kenmore ASPIRADORA 116.23513 User Manual
Page 20
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
k h ' i '
S f '
*
Review this table to find dO'it-yourseif solutions for minor performance problems. Any ser
vice needed, other than those described in this owner’s manual, should be performed by
an authorized Sears Service Center.
A
WARNING
Electrical Shock Hazard
Disconnect electrical supply before servicing or cleaning the unit.
Failure to do so could result in electrical shock or personal injury.
1 V>■■-»< tv. 1 1 Cleaner won’t start 1. Unplugged at wall outlet. al household service panel. 3. Loose hose electrical connections. 1. Plug in firmly, push ON/OFF switch to ON. 2. Reset dncuit breaker or replace fuse. 3. Reconnect hose ends, (page 7). Poor |ob of dirt 1. Full or dogged dust bag. 2. Clogged airflow passages. Dirty filters. 4. Wrong pile height setting. 5. Open suction control. 6. Hole in hose. S. Worn or broken bell. 10. Canister hood open. 1. Change bag, (page t4). 4. Adjust setting, (page 9). 5. Adjust control, (page 12). Replace hose. 7. Change agitator, (page 19). S & 9. See BELT CHANGING AND AGITATOR CLEANING, (pages 17-18). 10. Close and latch hood. Cleaner starts but 1. Hose or hood electrical connections. 2. Tripped overload protector in 3. Tripped thermal protector In canister. 1. Check connections, reconnect riose ends, (page 7). 2. Remove any items that may be caught or jammed, then reset. II cleaner starts and stops again, clean agitator and end caps, 3. Torn off and unplug the vacuum from oullel and wail approximately 50 minutes and plug the vacu POWER-MATE* will t)ot run when attached. 1. Power-Male* connections 2. Worn or broken belt. 3. Dirty agitator or end caps. 4. Tripped overload protector in 5. Switch not in CARPET position. 1. Plug in firmly, (page €). 2 & 3. See BELT CHANGING AND AGITATOR CLEANING, (pages 17-18), 4. Check agitator area for excessive lint end caps, then reset, (pages 12,17-18). 5. Move switch to CARPET position, (page 8). Constant green light on 1. Dirt passage is dogged. 2. Lenses are dirty. 1. Check lor clogs in sir passages, (page 14). 2. Clean lenses, (page 10). Any, some, or all red lights 1. Dirt passage is dogged. 1. Chedt for clogs in air passages, (page 14). No green or red dirt sensor lights. 1. Switch not in CARPET position. 2. No power lo sensor board. 1. Move switch to CARPET position, (page 8). Electronic/Mechanical activates. 1. Full or dogged dust bag. 2. Dirty fllteia. 3. Blocked airflow passage. 4. Certain altachmeni tods. 1. Change bag, (page 14). 2. Change filters, (page tS-16). Clear blockage from airflow passage, (page 14). 4. This is normal. Light should go off Cleaner picks up moveable 1. Wrong pile height setting. 2. Suction too strong. 1. Adjust setting, (page 9). 2. Open suction control, (page 12). Ught wont work. 1. Burned out light bulb. 1. Change light bulb, (page 18). Cord won’t rewind. 1. Dirty power cord. 2. Cord jammed. 1. Clean the power cord. Cleaner leaves marks on carpet 1. Wrong vacuuming pattern. 1. See VACUUMING TIPS, (page 9). 20
2. Tripped circuit breaker/blown fuse
pfck-up.
3.
7. Worn Rower-Mate* agitator.
9. Dirty agitator or end caps.
2. Clear airflow passages, (page 14).
3. Change filters, (page 15-16).
6.
cuts off.
Power-Mate*.
then reset, (pages 12,17-18).
um in, turn back on to see if the protector has
reset, (page 13]. Change dust bag, dear airflow
blockage, (page 14).
unplugged.
Power-Mate*
build-up or jamming. Clean agitator and
In dirt sensor.
in dirt sensor burn and never
turn green.
2, Take to your nearest Sears Service Center.
Bag/Tlose Check Indicator
3.
when tool is removed.
rugs-o^ POWER-MATE*
pushes too hard.
2. Pull out cord and rewind.