beautypg.com

When using air dry, Drum light, Damp dry signal – Kenmore ELITE OASIS 110.6707 User Manual

Page 22: Wrinkle guard® (30, 60, 90,150 minutes), Cyule signal, Cycle signal

Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".

background image

Air Dry

Use the Air Dry Modifier for items that require drying without heat
such as rubber, plastic and heat-sensitive fabrics. This table
shows examples of items that can be dried using Air Dry.

Type of Load

Time*

(Minutes)

Foam rubber - pillows, padded bras, stuffed toys

2 0 - 3 0

Plastic - Shower curtains, tablecloths

2 0 - 3 0

Rubber-backed rugs

4 0 - 5 0

Olefin, polypropylene, sheer nylon

1 0 - 2 0

* Reset cycle to complete drying, if needed.

When using Air Dry
■ Check that coverings are securely stitched.

■ Shake and fluff pillows by hand periodically during the cycle.

■ Dry item completely. Foam rubber pillows are slow to dry.

NOTE: Air Dry is not available with Auto Dry Cycles.

You can customize your cycles by selecting options.

O

ptions

. Drum Liyht

'■ Damp Dry Signal

) ■ Wrirskle Guard 90

Drum Light
On some models, you may select Drum Light to turn on the light
inside the dryer drum. During a cycle, if Drum Light is selected,

the drum light turns on and will remain on until DRUM LIGHT is
pressed again, the door is open and closed, or the door is left
open for 5 minutes.

When the dryer is not running, the drum light will turn on when

DRUM LIGHT is pressed or the dryer door is opened, and it will
remain on until the dryer door has been open for 5 minutes, the
dryer door is closed or DRUM LIGHT is pressed again.

Press DRUM LIGHT at any time to turn the drum light ON or OFF.

Damp Dry Signal
Select the Damp Dry Signal to alert you that your clothes are
approximately 80% dry or suitable for ironing. This is useful when

you want to remove lightweight items in a mixed load to avoid
overdrying or remove partially dry items that may need ironing.

The DAMP DRY SIGNAL is useful when drying bedsheets/linens
in a mixed load. When the signal goes off, open the door to stop
the dryer, rearrange the load inside the dryer, close the door and
restart the dryer to finish the drying cycle. Rearranging the load
will aid in the drying process.

NOTE: The Damp Dry Signal is available only with the Auto Dry
Cycles.

WRINKLE GUARD® (30, 60, 90,150 minutes)
WRINKLE GUARD® helps smooth out wrinkles that may form
when clothes are not removed promptly at the end of a cycle.

During this option, the dryer stops tumbling and then tumbles
again for a brief period without heat when pressed.

■ Press WRINKLE GUARD® to get heat-free, periodic tumbling

at the end of a cycle. WRINKLE GUARD® periodically starts
and stops the dryer, tumbling the load without heat for 30, 60,
90 or 150 minutes (depending on your model) unless you
open the dryer door,

■ Stop WRINKLE GUARD® at any time by pressing WRINKLE

GUARD®, opening the dryer door or pressing STOP.

■ For the Casual Cycle, WRINKLE GUARD® is preset to ON.

The other Auto Dry Cycles will retain the WRINKLE GUARD®
setting. For example, if you select WRINKLE GUARD® in the

Normal cycle, WRINKLE GUARD® will be on the next time you
select the Normal cycle.

NOTE: If you do not select WRINKLE GUARD®
after cool down.

the dryer stops

Cyule Signal

Cycle Signal

The Cycle Signal produces an audible sound when the drying
cycle is finished. Promptly removing clothes at the end of the
cycle reduces wrinkling.

Press CYCLE SIGNAL VOLUME until the desired volume (Loud or
Soft) is selected. On some models, press CYCLE SIGNAL to turn

the Cycle Signal On or Off.

Off

Ip ^-Soft

Cycle Signal Volume

Cycle Signal

NOTE: When WRINKLE GUARD® is selected, a tone sounds
every 5 minutes until the clothes are removed, or WRINKLE
GUARD® ends.

You can change Auto and Timed Cycles. Modifiers and Options
anytime before pressing Start.

■ Three short tones sound if an unavailable combination is

selected. The last selection will not be accepted.

Changing Cycles after pressing Start

1. Press STOP twice.

2. Select the desired cycle and options.

3. Press START. The dryer starts at the beginning of the new

cycle.

NOTE: If you do not press Start within 5 minutes of selecting the
cycle, the dryer automatically shuts off.

Changing Modifiers and Options after pressing Start
You can change a Modifier or Option anytime before the selected
Modifier or Option begins.

1. Press STOP once.

2. Select the new Modifier and/or Options.

3. Press START to continue the cycle.

NOTE: If you happen to press STOP twice, the program clears
and your dryer shuts down. Restart the selection process.

22

This manual is related to the following products: