Excessive heat around cookware on cooktop, Oven will not operate, Oven makes muffled ticking noise when in use – Kenmore 665.75022 User Manual
Page 22: Oven burner lights, then goes out after 1 minute, Oven burner flames are yellow or noisy, Oven temperature too high or too low, Display shows messages, Self-cleaning cycle will not operate, Cooktop cooking results not what expected, Baking results not what expected
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
Excessive heat around cookware on cooktop
Is the cookware the proper size?
Use cookware about the same size as the surface cooking
area, element or surface burner. Cookware should not extend
more than 1 in. (2.5 cm) outside the cooking area.
Oven will not operate
Is the power outlet properly wired and polarized?
Try another outlet to check for proper wiring and polarity.
Is this the first time the oven has been used?
Turn any one of the surface burner knobs on to release air
from the gas lines.
Is the electronic oven control set correctly?
See “Electronic Oven Control” section.
On some models, is the Oven Lockout set?
See “Oven Lockout” section.
Oven makes muffled ticking noise when in use
This is normal and occurs when the oven burner cycles on
and off to hold the set oven temperature.
Oven burner lights, then goes out after 1 minute
Press OFF/CANCEL, then wait 1 minute before trying again.
Is the power outlet properly wired and polarized?
Try another outlet to check for proper wiring and polarity.
Oven burner flames are yellow or noisy
m
Is propane gas being used?
The appliance may have been converted improperly. Contact
a trained repair specialist.
Oven temperature too high or too low
Does the oven temperature calibration need adjustment?
See “Oven Temperature Control” section.
Display shows messages
Is the display showing “PF"?
There has been a power failure. Press OFF/CANCEL to dear
the display. Reset the dock, if needed. See “Clock” section.
Is the display showing “F” followed by a number?
Press OFF/CANCEL to clear the display. If an “F” code
reappears, call for service.
Self-Cleaning Cycle will not operate
Is the oven door open?
Close the oven door all the way.
Has START/ENTER been pressed?
Press START/ENTER.
Has a delay start been set?
See “Timed Cooking” section.
Cooktop cooking results not what expected
Is the proper cookware being used?
See “Cookware” section.
Is the control knob set to the proper heat level?
See “Control Knobs” section.
Is the appliance level?
Level the appliance. See the Installation Instructions.
Baking results not what expected
Was the oven preheated?
Wait for oven to preheat before placing food in oven.
Are the racks positioned properly?
See "Positioning Racks and Bakeware” section.
Is there proper air circulation around bakeware?
See “Positioning Racks and Bakeware” section.
Is the batter evenly distributed in the pan?
Check to make sure batter is level in the pan.
Is the appliance level?
Level the appliance. See the Installation Instructions.
Are baked items too brown on the bottom?
Decrease oven temperature 15°F to 25°F (5“C to 15°C).
Are crust edges browning early?
Use aluminum foil to cover the edge of the crust.
Slow baking or roasting
Was the oven preheated?
Wait for oven to preheat before placing food in oven.
Is there proper air circulation around bakeware?
See “Positioning Racks and Bakeware” section.
Is the proper length of time being used?
Increase baking or roasting time.
Is the proper temperature set?
Increase temperature 25°F (15°C).
I Has the oven door been opened while cooking?
Oven peeking releases oven heat and can result in longer
cooking times.
22