While dishwasher is running, Electrical connection, Converting to built-in – Whirlpool DP3000XR Series User Manual
Page 14: Caring for simulated wood top, Connecting your portable dishwasher, When cycle is finished, Before starting
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
Connecting your portable dishwasher
A special adapter must be installed on the faucet before the dishwasher can
be connected. Complete instructions and the adapter are packed with your
dishwasher.
When moving yourdishwasher, make sure the
door is latched. Hold the dishwasher at the top
front corners.
Before starting
1.
Run water at faucet until it is
hot.
Turn it off.
PULL RING
Pull hoses out of their storage compartment
on the back.
LOCKING COLLAR
Pull down on the locking collar while lifting
the hose connector onto the faucet adapter.
When the connector snaps into place, re
lease the locking collar.
Turn the
hot
water on slowly until it is
all the
way on.
Plug in power supply cord.
See pages 8 and 9 to start the dishwasher.
While dishwasher is running
You can draw water from the faucet while the
dishwasher is connected.
DO NOT
draw water
while the dishwasher is filling or while water is
being pumped out. (This helps prevent a low fill
when dishwasher is filling, or mixing drain water
with fresh water.)
1. Press red button on hose connector to get
the water you want. (The faucet is set on hot.
Adjust faucet for the water you want.)
2. Be sure you return cold water to off, and
fhaf hot water Is full on.
When cycle is finished
Turn hot water off. (This can be done after the
iast rinse.)
Press the red button on the connector to re
lease the water pressure.
Lift slightly on the hose connector while pull
ing down the locking collar. Pull down on
the connector.
1
.
2
.
4. Empty any remaining water from the
connector.
5. Unplug power supply cord and return to
storage compartment.
6. Return hoses to storage compartment.
Electrical Connection
A power supply of 120 volts, 60Hz AC only, 15 or
20 amps, is required. For your personal safety,
this appliance must be grounded. This ap
pliance is equipped with a power supply cord
having a 3-prong grounding plug. To minimize
possible shock hazard it must be plugged into a
mating 3-prong grounding type wall recepta
cle, grounded in accordance with the National
Electrical Code and local codes and ordi
nances. If a mating wall receptacle is not avail
able, it is the personal responsibility and obliga
tion of the customer to have a properly
grounded 3-prong wall receptacle installed by
a qualified electrician.
A
WARNING: An extension cord
should not be used with this ap
pliance. Such use may result in a fire,
electrical shock or other personal injury.
3-Prong
Grounding Type
Wall Receptacle
3-Prong
Grounding
Plug
Power Supply Cord
DO NOT, UNDER ANY CIRCUMSTANCES, RE
MOVE THE POWER SUPPLY CORD GROUND
PRONG.
Converting to built-in
Your Whirlpool Portable Dishwasher can be
converted to a built-in (undercounter) model
by using conversion kit No. 569056. The kit is
available at your Whirlpool dealer or autho
rized TECH-CARE* Service Company. Instruc
tions are included with the kit.
Caring for
simulated wood top
The simulated wood top can be used as a
utility work surface for most kitchen jobs. It is
stronger and more easily cleaned than genu
ine wood.
The top can be used as a cutting board. Knife
marks will be visible but will not seriously
damage top. Hot items from the oven can be
placed on the top.
Clean with warm, soapy water. For dried-on
foods, use a scouring pad.
14