Panasonic CF-18 - Manual (Page 31)

8 Select [1. Yes, I agree to the provisions above and wish to
continue!].
This screen should appear.
4Win95wsf2000>
Select a number
1. Restore Windows(R) 2000 Professional to the whole HDD,
2. Make two partitions, for the operating system and data. And restore
Windows(R) 2000 Professional to the operating system partition.
{All existing partitions on HDD will be lost.)
3. Restore Windows(R) 2000 Professional to the first partition,
4. End
4Wlnclöw^Xßl
Select a number
1. Restore Windows(R) XP Professional to the whole HDD.
2. Make two partitions, for the operating system and data. And restore
Windows(R) XP Professional to the operating system partition.
(All existing partitions on HDD will be lost.)
3. Restore Windows(R) XP Professional to the first partition.
4. End
14 Press
At the confirmation message, select [Yes] and press
C Enter )■ (The Setup Utility settings will return to their
default values. Even the security settings with the excep­
tion of the password(s) will return to their default values.)
15 Press [ F10 ).
At the confirmation message, select [Yes] and press
C Enter) ■
16 Perform the setup procedure for Windows by following the
instructions on the screen. page 10 - 12)
note )-
When an UPDATE ED is to be created, follow the steps
in the readme.txt on the disk, (([^page 13)
77 Run the Setup Utility and change the settings where nec­
essary.
9 Make a selection from the menu.
• When selecting [2], enter the basic partition size for the
operating system installation and press C Enter ].
(The data partition size is the remainder after subtract­
ing the basic partition size.)
• To select [3], the initial partition size must be 6 GB or
more of the hard disk size. Reinstallation cannot be per-
fonued with a small partition size.
70 At the conflnnation message, press
CD
The operation of réinstallation for the hard disk starts au­
tomatically. (The operations take about 20 minutes Card-compatible> or 50 minutes .)
Do not cancel the reinstall procedure before it is
completed.
When a message appears instructing you to insert
the next CD, insert the recovery CD showing the
next number in the sequence, and then select [OK],
If the message 'The media docs not contain the cor­
rect file” appears, select [OK], A message will ap­
pear instructing you to insert the next CD.
Confirm that the proper recovery CD has been in­
serted by opening the tray of the CD drive and then
close the tray, then select [OK].
J
11 After the reinstallation procedure completes, press any key.
The computer will be shut down.
Remove the FIRSTAID FD and the floppy disk drive.
12 Remove the recovery CD and the CD drive.
13 Turn the computer on, and press ŒD while [Panasonic]
screen is displayed.
The Setup Utility will start up.
If the password has been set, enter the Supervisor Pass­
word.
the Panasonic KXL-RWli)AN>
Copy the necessary drivers, from the floppy disk included
with your CD drive, to the FIRSTAID FD with the method
below. It will be necessary to edit the CONFIG.SYS file
and AUTOEXEC.BAT file on the FIRSTAID FD. When
editing the AUTOEXEC.BAT file, some CD drives require
card managers (card and socket service). See the manual
included with your CD drive for further details.
(T) Start Windows and insert the FIRSTAID FD.
4WindöwsT2000l
Select [Slart]-[Programs]-[Acccssories]-[Notepad]-
[File]-[Open], input [a:\config.sys], then select [Open],
4Wincl0ws(XRi
Select [Start]-[AI1 Programs]-[Accessories]-[Notcpad]-
[File]-[Open], input [a:\config.sys], then select [Open].
(3) Rewrite the following line and save.
Delete the following four lines.
;KXL-RW10AN DRIVER
DEVICE=A:\TOOLS\KMASMGRA.SYS
DEVICE=A:\TOOLS\KMASASPA.SYS
DEVICE=A:\TOOLS\KMASCDA.SYS/D:MSCDOOO
Add the driver of your CD drive.
Device=A:\DRlVERl.SYS /D:MSCD000
^Rewrite this driver for the driver of your
CD drive. The driver for the PC Card will
also be necessary. Refer to the operation
manual that accompanies the CD drive.
Save the file and close [Notepad].
(4) Copy the CD driver file (i.e., the driver file rewritten in
step (3)) of the CD drive below [a:\] of the FIRSTAID
FD.
(5) Set the floppy disk to the write-protect state.
After this, follow the reinstalling procedure of
using the Panasonic CD drive KXL-RW10AN>.
(C? page 30)
31