Clarion DXZ938R - Manual (Page 9)

DXZ938R
13
English
3. When the adjustment is complete, press the
[A-M] button several times until the function
mode is reached.
Operation BASS/TREB
1. Press the “BASS/TREB” mode. Each time
the [EQ] button is pressed, the adjusting item
“BASS” or “TREB” is changed cyclically.
2. Turn the [ROTARY] knob clockwise or coun-
terclockwise to adjust “BAS/TREB”.
3. Press the [EQ] button to return to the previ-
ous mode.
∗
The Adjustment range is from -6dB to +6dB
for bass and treb.
∗
This parameter is reflected STD PRO mode
Speaker Setting
You can set up your favorite sound environment
using “Dolby Surround Pro logic
II ” or “AC-
Processor II ” so that you can enjoy a dynamic
sound of 5.1 ch surround or 4ch + 2ch speaker.
● Dolby Pro Logic II 5.1ch surround
Center SP +Front L.R. +Surround L.R. +Sub
Woofer.
To make the most of the sound field reproduc-
tion of Dolby Pro Logic
II , a speaker system of
5.1 channel is recommendable. It has been also
designed so that a sound filed effect almost as
good as that of 5.1 channel reproduction can be
obtained even by a constitution of 4 channel + 1
channel (subwoofer).
If you using Dolby Pro Logic source and your
speaker is only four Front L.R. + Surround L.R.,
speaker setting will be better to CTR+SW and
CTR OFF, so Center channel divided to Front
L.R. automatically.
Note
• When SW-L + SW-R are chosen, audio output
from SW-L is not available in the PL II mode.
● AC- Processor II
Front L.R. + Rear L.R.+ Sub Woofer L.R. (4ch +
2ch)
To make the most of the sound field reproduc-
tion of AC-Processor
II , a speaker system of 4
channel + 2 channel is recommendable.
1. Press and hold the [TITLE] button for 1 sec-
ond or longer and enter “ADJ” mode.
2. Press the [ a ] or [ d ] button to select the
“SP-SETTING”.
3. Turn the [ROTARY] knob clockwise or coun-
terclockwise to select “SW L+SW R” or “CTR
+SW” mode.
Basic Operations
Note:
• When CTR + SW are chosen, audio output from
CTR is not available except in the PL II mode.
Center Speaker and Sub Woofer On / Off
Select PL II Mode on and SP setting to
“CTR+SW” mode
1. Press and hold the [TITLE] button for 1 sec-
ond or longer.
2. Press the [ a ] or [ d ] button to select the
“SP SEL”.
3. Press the [ ] button to adjust the “CTR-
SP” “SUB W”.
4. Turn the [ROTARY] knob clockwise or coun-
terclockwise to select “ON” or “OFF”.
∗
This function is useful for Speaker Setting
Problems.
Filter Adjustment
1. Select Dolby Pro Logic II or AC-Pro II mode
and press and hold the [TITLE] button for 1
second or longer.
2. Press the [ a ] or [ d ] button to select the
“FILTER”.
3. Press the [ ] button to adjust the “SUB-W
LPF” or “HPF”.
4. Turn the [ROTARY] knob clockwise or coun-
terclockwise to adjust filter frequency.
∗
Sub Woofer Low Pass Filter Adjustment
Range is 50, 80, 120Hz (18dB/oct), OFF.
∗
When PL II mode Sub Woofer Low pass Filter
Adjustment Range is 50, 80, 120Hz (12dB/
oct.), OFF.
∗
High Pass Filter adjustment Range is 50, 80,
120Hz(12dB/oct), thrgh.
Note:
• High pass filter adjustment is available for Front
2ch and Rear 2ch only AC-Pro II PRO Mode.
CT (Clock Time) function
The CT function receives CT data sent from an
RDS station and displays the time. Press the
[DISP] button to switch to the CT display.
∗
If a CT data is not being received, “CT––:––” ap-
pears in the display.
Note:
• CT data is not transmitted in some countries and
by some broadcast stations. Also, in some areas,
the CT may not display accurately.