Clarion DXZ938R - Manual (Page 8)

12
DXZ938R
English 6. OPERATIONS
Basic Operations
Note:Be sure to read this chapter referring to the front diagrams of
chapter “2. CONTROLS” on page 5 (unfold).
CAUTION
Be sure to lower the volume before switch-
ing off the unit power or the ignition key. The
unit remembers its last volume setting. If you
switch the power off with the volume up,
when you switch the power back on, the sud-
den loud volume may hurt your hearing and
damage the unit.
Turning on/off the power
Note:
• Be careful about using this unit for a long time
without running the engine. If you drain the car’s
battery too far, you may not be able to start the
engine and this can reduce the service life of the
battery.
1. Press the [FNC] button.
2. The illumination and display on the unit light
up. The unit automatically remembers its last
operation mode and will automatically switch
to display that mode.
3. Press and hold the [FNC] button for 1 second
or longer to turn off the power for the unit.
Note:
• System check
The first time this unit is turned on after the wire
connections are completed, it must be checked
what equipment is connected. When the power is
turned on, “SYSTEM CHCK” and “PUSH
POWER” appear in the display alternately, so
press the [FNC] button. The system check starts
within the unit. When the system check is com-
plete, the power is turned off, so press the [FNC]
button again.
Selecting a mode
1. Press the [FNC] button to change the opera-
tion mode.
2. Each time you press the [FNC] button, the
operation mode changes in the following or-
der:
Radio mode ➜ DAB mode ➜ CD mode ➜
DVD DECK mode ➜ CD changer mode ➜
MD changer mode ➜ DVD changer mode ➜
TV mode ➜ AUX mode ➜ Radio mode...
∗
External equipment not connected with
CeNET is not displayed.
Adjusting the volume
Turning the [ROTARY] knob clockwise increases
the volume; turning it counterclockwise de-
creases the volume.
∗
The volume level is from 0 (minimum) to 33 (maxi-
mum).
Switching the display
Press the [DISP] button to select the desired display.
Each time you press the [DISP] button, the dis-
play switches:
∗
Once selected, the preferred display becomes the
display default. When a function adjustment such
as volume is made, the screen will momentarily
switch to that function’s display, then revert back to
the preferred display several seconds after the ad-
justment.
∗
When you have entered a title in a CD/MD, it ap-
pears in the main display. If you have not entered a
title, “
D NO-TITLE” or “ T NO-TITLE” appears in
the title display instead. For information on how to
enter a title, refer to the subsection “Entering titles”
in section “Operations Common to Each Mode ”.
∗
When CT data is not received, “CT––:––” appears
in the display.
Adjusting the balance
1. Press the [A-M] button and select “BAL-
ANCE”.
2. Turning the [ROTARY] knob clockwise em-
phasizes the sound from the right speaker;
turning it counterclockwise emphasizes the
sound from the left speaker.
∗
The factory default setting is “0”. (Adjustment
range: L13 to R13)
3. When the adjustment is complete, press the
[A-M] button several times until the function
mode is reached.
Adjusting the fader
1. Press the [A-M] button and select “FADER”.
2. Turning the [ROTARY] knob clockwise em-
phasizes the sound from the front speakers;
turning it counterclockwise emphasizes the
sound from the rear speakers.
∗
The factory default setting is “0”. (Adjustment
range: F12 to R12)