Clarion DXZ938R - Manual (Page 10)

14
DXZ938R
English
AC-Processor II Operation
Dolby Pro Logic II
Dolby Pro Logic II is a matrix decoding technol-
ogy in which the updated digital matrix technol-
ogy is applied and Dolby Pro Logic is further im-
proved. It realizes excellent 5.1 channel repro-
duction of Dolby surround source as well as ste-
reo sound sources such as CDs, thereby caus-
ing a surround channel to be full-ranged (20 Hz
to 20 kHz) and become stereo. Therefore, you
can enjoy any stereo sources with dynamic
sound of 5.1 channel. According to a source to
be reproduced, Music Mode or Matrix Mode can
be selected.
∗
Manufactured under license from Dolby Laborato-
ries. “Dolby”, “Pro Logic” and the double-D sym-
bol are trademarks of Dolby Laboratories.
● Music Mode
This mode is suitable for stereo sources like
CDs. By optimizing frequency characteristics of
the surround channel, a broader and deeper
sound is assured. In addition, since broadness
of the sound field varies with recording condi-
tions of music sources, there is Adjusting Mode
which makes a finer tuning available.
● Matrix Mode
This mode is suitable for AM/FM radio.
Selection and switching of the
Dolby Pro Logic
II effect
While the “Dolby PL II ” indication is lit in the dis-
play, the “Dolby PL II ” effect is set to “On”.
1. Setting the speaker 5.1ch ( For detail, see the
section Basic Operation - Speaker setting).
2. Press the [PL II ] button so that PL II mode is
turned on. Each time the button is pressed,
the mode changes as follows: “MUSIC
MODE”
➜ ”MATRIX MODE” ➜ ”PL II OFF
MODE” ➜ ”MUSIC MODE”
3. Select the “PL II OFF MODE” to turn off the
Dolby Pro Logic II effect. Also press the
[VSE] button or [EQ] button to turn off the
Dolby Pro
II .
Adjusting Dolby Pro Logic II Operation
1. Select Dolby Pro Logic II mode and press
and hold the [TITLE] button for 1 second or
longer to enter “ADJ” mode.
2. Press the [ a ] or [ d ] button to select the
“PL II DELAY”.
3. Press the [ ] button to adjust the “PL II
DELAY”.
4. Turn the [ROTARY] knob clockwise or coun-
terclockwise to make the adjustment.
∗
The adjustment range of surround speaker de-
lay is from 0m sec. to 15m sec.
∗
The adjustment made in “PL II DELAY” is re-
flected in the each mode.
Adjusting Music Mode
Use the MUSIC MODE to make more detailed
adjustments.
1. Select “Music Mode” and press and hold the
[TITLE] button for 1 second or longer.
2. Press the [ a ] or [ d ] button to select the
“PL II CONT”.
3. Press the [ ] button to adjust the “PL II
CONT” detail items.
4. Press the [ a ] or [ d ] button to select the
items.
5. Turn the [ROTARY] knob clockwise or coun-
terclockwise to make the adjustment.
∗
The detailed adjustments depend on each of
the adjustment items. There are 3 items:
“PANORAMA”, “DIMENSION”, and “CTR
WIDTH”.
PANORAMA (Y or N):
Selecting PANORAMA mode will extend the
front sound field image to the rear. If sur-
round effect does not seem to be presented
sufficiently, select the setting position “Y”.
DIMENSION (0 to 6):
Selecting DIMENSION mode will shift the
sound field image to the front or the rear. If
the balance of the sound field image is too
much pulled towards the front or rear, the
balance front/rear can be corrected The ad-
justing value 3 is the center position. The
range of 3 to 0 shifts the balance front/rear to
the front. The range of 3 to 6 shifts the bal-
ance front/rear to the rear.
CTR WIDTH (0 to 7):
Selecting CTR WIDTH mode will adjust the
localization of the center channel between
the center speaker and the front speaker L/R.