Yamaha PSR-400 - Manual (Page 14)

FEATURE REFERENCE
( overall control )
Setting the Pitch Bend Range
The maximum amount of pitch bend produced by the
PITCH BEND wheel can be set anywhere from ±1 semi­
tone to ±12 semitones (i.e. plus or minus one octave).
1. To set the pitch bend range, roll the PITCH BEND
wheel all the way in either direction so that the current
range value appears on the MULTI DISPLAY.
PITCH BEND tl‘
■ . CJOW
■ I
STYLE ! SPLIT VOICE VÇHÇ^
c
STYLE SPLIT VOICE B£>T
2. Use the ACCOMP. VOLUME (PITCH BEND
RANGE) [A] and [T] buttons to set the desired range
— the pitch bend range value is displayed in semitones
(-12 through 12). If a minus setting is selected pitch
bend wheel operation is reversed — i.e. roll the wheel
away from you to lower pitch.
PITCH BEND MANGE
r
¿hi
ftCCOMF
VOLUME
y
3. Release the PITCH BEND wheel.
When this parameter has been changed, be sure to store the
new data to a PAGE MEMORY (see page 13). If this is not done
the newly selected data will be lost when a different PAGE
MEMORY Is selected.
TRANSPOSE
The PSR-400/PSR-500 [TRANSPOSE] buttons makes
it possible to shift the pitch of the PSR-4(X)/PSR-500 up or
down in semitone intervals up to a maximum of 12 semi­
tones (one octave). Transposing the pitch of the PSR-4(X)/
PSR-500 keyboard makes it easier to play in difficult key
signatures, and you can simply match the pitch of the
keyboard to the range of a singer or other instrumentalist.
A
TRANS
POSE
STYLE/SPLIT VOICE
n
u
style split VÛJCE
The TRANSPOSE [A] and [T] buttons are used for
transposition. Press the [A] button to increase the pitch of
the keyboard, or the [T] button to lower the pitch. The
selected degree of transposition will be displayed on the
center two digits of the MULTI DISPLAY while the
TRANSPOSE
[A] or [▼] button is pressed, and for ap­
proximately 2 seconds after either TRANSPOSE button is
released.
The transposition range is from -12 to +12, with -12
corresponding to downward transposition by 12 semitones
(one octave, and +12 corresponding to upward transposi­
tion by 12 semitones. 0 is the “normal” keyboard pitch
value. The normal transpose value (0) can be recalled at
any lime by pressing both the TRANSPOSE
[A] and [T]
buttons at the same time.
• The TFIANSPOSE function will not work while any keys are held.
• TRANSPOSE does not affect the percussion voices (numbers
94 through 99).
• When this parameter has been changed, be sure to store the
new data to a PAGE MEMORY (see page 13). If this is not done
the newly selected data will be lost when a diUerent PAGE
MEMORY is selected.
TUNING
The PSR-400/PSR-500 [TUNING] buttons makes it
possible to tune the pitch of the PSR-400/PSR-500 to
match other instruments. Tuning can be accomplished
over a ±50-cent range (that’s 100 cents total, or one semi­
tone) in 16 steps.
TUNING
STYLE / SPLIT VOtCE
u u TÌ n
T
tu.u
style split voce
The TUNING [A] and [T] buttons are used for tuning.
Press the [A] button to raise the pitch of the instrument, or
the [T] button to lower the pitch. The selected degree of
tuning will be shown on the MULTI DISPLAY in Hertz
while the TUNING
[A] or [T] button is pressed, and for
approximately 2 seconds after either TUNING button is
released.
The tuning range is from 427.5 Hertz (-50 cents) to ^
452.9 Hz (+50 cents). 440.0 Hertz (±0 cents) is the “nor­
mal” tuning value. The normal tuning value (440,0) can
be recalled at any time by pressing both the TUNING [A]
and [T] buttons at the same time.
• TUNING does not affect the percussion voices (numbers 94
through 99).
• When this parameter has been changed, be sure to store the
new data to a PAGE MEMORY (see page 13). If this is not done
the newly selected data will be lost when a different PAGE
MEMORY is selected.
TEMPO
The TEMPO buttons control the tempo of the AUTO
ACCOMPANIMENT, the SONG MEMORY, DEMO
playback, and the MULTI PADs on the PSR-5CX).
¿h
TEMPO
STYLE/SPUT VOICE VOCE
f pn
IC U
style split voce beat
12