Ttm56man.pdf, Ttm 56, Operators manual – Rane TTM 56 User Manual
Page 3: Manual, Performance mixer, Quick start

Manual-
TTM 56
PERFORMANCE MIXER
OPERATORS MANUAL
Quick Start
Congratulations! You are the proud owner of an exceptional
performance instrument. Experienced turntablists will find the
TTM 56 comfortable and familiar. The TTM 56 has many unique
features which are mastered quicker if you read the manual. Right!
We know you can’t resist jumping right in, but please read at least
this portion of the manual. It will help you get a good start.
About the faders: The program faders and crossfader are magnetic,
non-contact faders. This means No travel noise – No bleed – Ever!
The electrical performance of the faders is unaffected by use. Old
habits are hard to break, but you really don’t have to mess with
these faders. The magnetic faders in this mixer are very different
from what you are used to. Be sure and read the Q and A section
on page Manual-8.
Special Features:
• Program fader MODE switches allow selecting two sets of
curves:
MODE 1
gives the familiar stereo fader response.
MODE 2
gives a left/right pan effect.
• Both curves allow continuous adjustment of CONTOUR, giv-
ing smooth blend or fast cut.
• The CHANNEL REVERSE switch allows the left-hand or
right-hand fader to control PGM 1 or PGM 2.
WEAR PARTS: This product contains the following wear parts subject to the ninety (90) day warranty period described on page
Warranty-1: ST 2 Phono/Line Switch Assembly (2).
• The CROSSFADER MODE switch allows selecting two sets of curves:
MODE 1
gives the familiar PGM 1 to PGM 2 cross-fade response.
MODE 2
gives a center cut response (PGM 1 and PGM 2 are off in the center).
• Independent CONTOUR controls for each side of the crossfader allow cut on one side and blending on the other (or any combination).
• Auxiliary Inputs and Outputs, with independent level controls, give session mixing ability.
AUX
Inputs may be used for a drum machine, tape, etc.
AUX
Input is after the crossfader and after the effects loop.
AUX
Outputs may be used for recording, booth monitoring, or a second zone.
AUX
Output is the same as the Master Mix.
• FlexFX™ allow assignment of PGM 1, PGM 2 or both to the effects loop. The effects loop is post-fader. You get great results when us-
ing the program faders or crossfader with reverb or other delay effects. WET/DRY pan lets you control how much effect is in the mix.
• Three-band Accelerated-Slope™ EQ allows full cut of each band. The EQ engage switch lets you A/B compare or quickly transform the
EQ effect.
• Two 10-segment meters provide dual-mono-Cue or stereo-Master operation.
• Yes, we included a power switch on the rear.
The flexibility of the TTM 56 faders can result in some initial confusion. We highly recommend trying one thing at a time to avoid
this. Make sure the CHANNEL REVERSE switch is off. Start by changing the Mode and Contour of each fader, one at a time. See the dia-
grams on pages Manual-6-7 to understand the fader responses under different settings. Once you understand the controls, start creating!
MIC
LEVEL
HIGH
LOW
HIGH
GAIN
GAIN
HIGH
MID
EQ
EQ
MID
AUX OUT
LOW
FlexFX
FlexFX
LOW
PHONES LEVEL
PGM 2
PGM 1
MASTER
OL
10
0
+12
-12
+12
-12
+6
OFF
+6
OFF
+6
OFF
+6
OFF
+6
OFF
+6
OFF
10
0
6
4
2
8
6
4
2
8
10
0
6
4
2
8
10
0
6
4
2
8
10
0
6
4
2
8
10
0
6
4
2
8
AUX IN
+10
+7
+4
+2
0
-4
-2
-7
-10
-20
10
0
6
4
2
8
PERFORMANCE MIXER
FAST
SLOW
TTM 56
L
REVERSE
CONTOUR
REVERSE
MODE 1
MODE 2
CONTOUR
MODE 1
MODE 2
CHANNEL REVERSE
TRANSFORM
TRANSFORM
STEREO HOUSE
MONO PGM1 / PGM2
A
B
PAN
R
DRY
WET
L
PAN
MASTER / CUE
R
PGM 1
CUE
PGM 2
REVERSE MODE 1 MODE 2
FAST
SLOW