4parts list – Wilbur Curtis D1000GT User Manual

Page 4

Parts List

Guidelines for Pulse Brew:

This feature allows tuning of the coffee flavor. The pot level should always be set first with this option OFF. Depending on your grind

profile and water conditions, the five Pulse Brew options help “tune” or change the coffee flavor. Filter Pack type coffees typically

extract better with the A and B pulse setting. Decaffeinated coffees typically extract better with the B pulse setting. High-Yield coffees

typically extract better with the C pulse setting. Of course, any of the A, B or C settings may be used to suit your taste profile. There are

two additional settings (D and E) that allow you to manually set the ON TIME pulses and OFF TIME.
If Pulse Brew is selected (ON), Cold Brew Lock is set to Delta 1 within 5º F of set point. Cold Brew Lock and Pre-infusion disappears

from the list of program selections. When Pulse Brew is ON, Pre-Infusion disappears from the list of program selections.
Display Brew Time (Factory set to ON)

Press  to display ON or OFF. Pressing either < or > toggles between on and off.  to set. When on, the Display Brew Time feature

allows you to see the remaining time in the brew cycle counting down.

Drip-Out Mode (Factory set to 2 min)

Press  to select. Press > to increase time (to a maximum of 5 minutes) or < to decrease the time and turn OFF. Time counts up in 5

second increments. Press  to set.

Display Messages (Factory set to ON)

Press  to turn ON or OFF. The message displayed is “Rinse Server Before Brewing”. This message will alternate; two seconds with

Rinse Server Before Brewing, then Curtis READY TO BREW will appear for six seconds.
Exit

Press  to select, exits program mode and returns unit to operation. Pressing > returns you to Brew By Volume.

Exit

Drip-Out

Mode

Display Brew

Time

Drip-Out

Mode

BREW CONE, W/HANDLE ASSY 7.1”D

BREW CONE, ASSY S.S. (OPTIONAL)

COVER, TOP

VALVE, DUMP VALVE LEFT 120VAC 10W

VALVE, DUMP LEFT 220V 12W

KIT, FITTING SPRAYHEAD KYNAR

VALVE, DUMP RIGHT 120V 12W

VALVE, DUMP RIGHT 240V 9W

BRACKET, UCM

KIT, UCM & OVERLAY D1000GT

CONTROL MODULE, 220V D1000GT/H

LABEL, DUAL UCM PANEL

COVER, FRONT D1000GT

FAUCET, HOT WATER W/JAM NUT

SEAT CUP, SILICONE (USE ON WC-1809)

HEAT SINK, 1 PH ASSEMBLY

SPRAYHEAD, PURPLE ADVANCE FLOW

CAPACITOR, X2

LEG, GLIDE 3/8-16 STUD SCREW

LEG, 3/8-16 STUD SCREW

TANK, COMPLETE D1000GT 220V

TANK, COMPLETE D1000GT/H 120/220V DV

VALVE, INLET 2 GPM

VALVE, INLET 1 GPM 240V 10W

SWITCH, TOGGLE NON-LIT DPST 25A 125/250V

KIT, VALVE REPAIR USE ON WC-889 /WC-817

GRID, DRIP TRAY AIRPOT (OPTIONAL)

TUBING, SILICONE, 5/16” I.D. ( 1 FT.)

KIT, PROBE WATER LEVEL W/NUT & O’RING

ELEMENT, HEATING 2.5W 220V

GUARD, SHOCK HEATING ELEMENT

SENSOR, TEMPERATURE TANK

GUARD, SHOCK RESET THERMOSTAT

THERMOSTAT, HI LIMIT HEATER CONTROL

COMPOUND, SILICONE 5 OZ TUBE

KIT, HEATING TANK LID

KIT, VALVE REPAIR USE ON WC-847

Item № Part №

Description

17A

18A

WC-3316-101

WC-3316

WC-5421

WC- 889*

WC- 860

WC-2962-101K

WC- 817*

WC- 861

WC-67101

WC-37177*

WC- 789

WC-39396

WC-5847

WC-1809

WC-1806

WC-8560

WC-29025*

WC-8591*

WC-3518

WC-3503

WC-75285

WC-75284

WC- 847*

WC- 856

WC- 103*

WC-3763*

WC-6221

WC-5310*

WC-5502-01*

WC- 934-04*

WC-4394

WC-1438-101*

WC-43055

WC- 522

WC-5231*

WC-37008*

WC-3765L*