beautypg.com

Sony RM-V60 User Manual

Rm-v60, S o n y, Remote commander

Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".

background image

S O N Y

Remote Commander

RM-V60

Operating Instructions

© 1997

by Sony Corporation

Printed in China

For the customers in the U.S.A.

WARNING

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to pro\ ide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. Howe\'er, there is
no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

You are cautioned that any changes or modifications not expressly
approved in this manual could void your authority to operate this
equipment.

For the customers in Canada

The DBS operation works only for digital satellite broadcast system
in the U.S.A.

Setting Up the Remote Commander

Before you can start using the Commander, you must first set it up.
This manual describes everything you need to know to set up the
Commander, including:

• Installing the batteries.
• Presetting the Commander with the codes for your TV, VCR, Cable

box, DBS tuner, and other audio components.

- Presetting the Remote Commander

The Commander is preset at the factory to operate Sony brand
components.
If you're using the Commander with a Sony component, you won't
need to preset the Commander before you start using it.
To set up the Commander to use with other (non-Sony)
manufacturers' components, you'll need to follow the instructions in
this manual to preset the Commander with the correct code number

for your components.

3-861-126-11(1)

Button

Component that can be presetFactory setting

TV

TV

Sony TV

VCR

VCR

Sony VHS VCR
(VTR3)

DBS/CBL DBS tuner/Cable box

Sony DBS tuner

RECEIVERReceiver

Sony Receiver

CD

CD player

Sony CD player

TAPE

Tape deck/MD deck/DAT deck

Sony tape deck

AVI

VCR/Cable box/DBS tuner/

Sony 8n\m VCR

LD player/Receiver/CD player/

(VTR2)

AV2

Tape deck/MD deck/DAT deck

Sony LD player

Note

The Commander can be set up to operate only one component per
button - unless their code numbers happen to be the same. For
example, you cannot set up the Commander to operate a Sony TV
and a Panasonic TV simultaneously (because they use different code
numbers).

Installing the Batteries

Slide open the battery compartment and insert two size AA (R6)
batteries (not supplied).

Be sure to line up the

+

and - on the batteries with the -r and - on the

battery compartment.

When to replace the batteries

Under normal conditions, batteries will last up to six months. If the
Commander does not operate properly, the batteries might be worn
out. When the display dims, replace the batteries with new ones.

Notes

• Replace both batteries with new ones.
• Do not take more than 20 minutes to replace the batteries;

otherwise, your setting of the code numbers will be erased.

Notes on Batteries

• Do not mix old batteries with new ones or mix different types of

batteries together.

• If the electrolyte irrside the battery should leak, wipe the

contaminated area of the battery compartment with a cloth and
replace the old batteries with new ones. To prevent the electrolyte
from leaking, remove the batteries when you plan not to use the
Commander for a long period of time.

Setting the Code

Follow the steps 1 and 2 below for each component you plan to use
with the Commander.

Step 1; Entering the Code Number

1

See the tables in "Component Code numbers", and find the code

number in double figures for the desired component.
If more than one code number is listed, use the number that's
listed first to complete the steps below.
For example, if you're setting up a Philips' VCR, you would use
the codé number 13.

If your component isn't listed, see "Searching for the Correct
Code".

2'

Press the SET button with a bail-point pen tip etc., and release it.

S E T

©

Display window