Sony RM-V18A - Manual (Page 3)

Changing the Factory Setting for the
Volume Control
1 Prt'ss and release the S (set) button. s")
2 Press the AVI button. AVI
Remote Button Descriptions
3 Press the VOL+ button.
4 Press the ENTER button.
(±1
The volume control setting is changed to "Receiver/amplifier." You
can control the volume of the receifcer (or amplifier) of the
AV1
button while selecting any component.
Notes
• If you are using more than one receiver (or amplifier) and have set
it on the CABLE or AV2 button, when selecting these buttons you
cannot control the volume of the receiver (or amplifier) of the AVI
button.
• If you change the setting of the AVI button to a component other
than a receiver or amplifier, the volume control setting of video
components will return to "TV" even if you have changed the
factory preset volume control. In this case, you will not be able to
control the volume from audio components other than a receiver
or amplifier.
To reset to factory preset volume control
In step 3 above, press VOL- instead.
Operating a Component
C
VCR CABLE
.... il.... ~T
c AVI AV2
I I • :
1 Press button of the desired
component on ti\e Commander.
2 Point the Commander directly at the
component.
3 Press the button for the function you want to use.
See "Remote Button E>escriptions" for complete descriptions of the
buttons on the Commander.
Notes on Using the Remote Commander
Basically, use this Commander in the same way as the Commanders
supplied with your components.
• Using this Cbmmartder will not increase the functions of your
components. The functions of the Commander are limited to the
functions of the components themselves. For example, if your TV
does not have a MUTING function, the
MUTING button on this
Commander will not function with your TV.
• Some functions of the component may not work with this
Commander.
• If your cable box can control volume, be sure to set its volume
switch to a medium position. If the volume on the cable box is
turned down completely, you will not be able to adjust your TV's
volume with the Commander.
Operating a TV
in 1 o set up the Commander.
To change the input mode.
S] To change the channel. For example, to
change to channel 5, press 0 and 5 (or,
press 5 and ENTER).
To display the current channel on TV.
To move the cursor upward,
downward, to the right, or to the left.
To call up the MENU display.
f7l Volume up: +
Volume down: -
8] To mute the volume on the TV.
^ To turn on and off.
19 To switch to TV operation. Press the
button on which the TV is assigned.
[ll] To operate the Picture-in-Picture
function.
Pressing each button while pressing the
PIP button operates as the table below,
in To operate SLEEP function on the TV.
(Works oi\ly for a TV with the SLEEP
function.)
09 To enter the selection
03
Channel up: +
Channel down: -
01 To operate JUMP, FLASHBACK or
CHANNEL RETURN function on the TV
depending on the setting of the TV's
manufacturer.
PIP operations
Press To
PIP and DISP Turn on/off the "window" picture.*
PIP and ENTER Turn off the "window" picture.
PIPandCH+orCH- Change the TV channel in the "window" picture.
PIP and TV'/VIDEO Change the input mode of the "window" picture.
PlPandl Move the location of the "window" picture.
PIP and 2 Swap the "main" picture and the "window" picture.
PIP and 3 Freeze the "window" picture.
• If the "window" picture does not turn off this way, try pressing ENTER whik
pressing PIP.
Operating a VCR
m To set up the Commander.
IS To switch to VCR operation. Press the
button on which the VCR is assigned.
5] To switch the signals supplied to the TV
(from antenna or VCR).
[4] To change the charmel.
For example, to change to channel 5,
press
0 and 5 (or, press 5 and ENTER).
ISl To display the on-screen menu (Sony
VCR only).
6] To play.
T\ To rewind.
51 To record, press ► while pressing •.
^ To turn on aiul off.
g To fast-forward.
To stop.
Ï9 To pause.
Ü Channel up: +
Channel down: -