Sony ICF-SC1 - Manual (Page 9)

Running Programmable Scanning
1
I loM down I \ I ld\ and press SC AN Uphth’ (i.o., !e^
than I second).
Scanning will start trom the lower limit trequenc\‘.
2
Adjust the SQl. control (see page 11).
V
(,'*iKv \’ou haw do
dotin«,' il ac,ain as I
raiigo. 'd a scanning rani;o, wni do not need to
; as \ ou are soannino, the same rn'i.juon«. \
Notes
•Do not press SCAN tor I second or longer while holding down
h\ !‘hl\. It \ on do, the recewer will enter the S-second pause
mode and the decimal point \% ill tiash in the displaw See
".Adjusting scanning pause time", (page at)'.
•it \ ou tr\- to run I’rogrammable Scanning with an invalid range
detinition (i.e., the specified upper and kiwer limits are tlie same
treLjuenev, or, either or both limits have not been specified), the
receiver will display the memorv content of the two frequencies
and then return t^i the prex ious status.
•During brngrammable Scanning, the receix er will start scanning
from the lower of the two specified frequencies. Thus, if, for
example, the frequency memorized under PRESET I. is higher
than the frequenev memorized for PRESET U, scanning will start
from the frequenev in PRESET U.
•Although the upper and lower limit frequencies are located after
channel 30 in page 10, thex’ do not belong txi this page; thev will
not be scanned when page 10 is targeted in Memory Scanning.
To display the current scanning range
Press PAGE, then "10/0", then EXE. Page 10 will appear
in the display.
Press PRESET, then + or - repeatedly until "PRESET L" or
"PRESET U” appears for the preset number display-
To change scanning direction
Press + or - .
Service Scanning
Serv ice Sc.iniiing sc.ins one of the S pre-progmmmed
Public Service Bands of your choice. .X button is assigned
to each of the bands for instant access.
Pre-programmed Public Service Bands
Service Band Key number
VVX (NOAA VVKATHER broadcast) 1 _
POLICE
2
FIRE/FMC (Fire and emergenev) 3
MARINE 4
AIB(V) (AircraftlVHFI) .3
AIR(U) (AircraftIUHFI) 6
FM broadcast 7
TV{V) a'V soundIVHFl) 8
TV(U) (TV soundlUHFI) 9
1
2
3
Set the SQL control to MIN.
Press POWER to turn the receiver on.
Press SVC.
The receiver will enter the Service Scanning mode.
"SVC SCAN" will flash in the display.
page 1 y I I I I M /
man - 1
DEM y m^pvn SCAN 1
\
AM
ir nnri
L J.ULIU MHz
4
Press the number key for the Public Service Band of
your choice.
2 (POLICE band) is shown here as an example.
To resume scanning manually during scanning
pause
Press + or ~ .
Note
When presetting or recalling a irequency in preset I. or U, you can
also recall these cliannels bv pressing "31" (for preset L) or "32"
(for preset "L") and then E,\E.
page 1
j
DEMY SVC SCAN L
NFM
J ~l n jn
J UJLIJ MHz
5
Adjust the SQL control (see page 11).
To exit Service Scanning
Press SVC when the "SVC SCAN" indication is flashing
in the display. The receiver will return to the previous
status.
Notes
»If vou skipped step 4 (pressed EXE when the "SVC SCAN"
indication IS flashing in the display), scanning will start on the
Service Band number displayed at that point.
•If the "SVC SCAN" indic.ition is left flashing for about 5 seconds,
scanning will start on the Service Band number displayed at that
point.
16 17