Great Plains 1005NT Assembly Instructions - Manual (Page 2)

123-535M 06/02/2008
Table of Contents
© Copyright 1995, 2006, 2008. All rights Reserved.
Great Plains Manufacturing, Inc. provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has been taken in the preparation
of this manual, Great Plains Manufacturing, Inc. assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the infor-
mation contained herein. Great Plains Manufacturing, Inc. reserves the right to revise and improve its products as it sees fit. This publication describes the state of this product at
the time of its publication, and may not reflect the product in the future.
Great Plains Manufacturing, Incorporated Trademarks
The following are trademarks of Great Plains Mfg., Inc.: Application Systems, Ausherman, Land Pride, Great Plains
All other brands and product names are trademarks or registered trademarks of their respective holders.
Printed in the United States of America.
7ft and 10ft EWNT Small Seeds Great Plains Manufacturing, Inc.
Important Safety Information.................................... 1
Introduction ................................................................ 3
Description of Unit........................................................ 3
Compatible Drills.......................................................... 3
Available Kits ............................................................... 3
Using This Manual ....................................................... 4
Definitions ................................................................ 4
Call-Outs .................................................................. 4
Owner Assistance ........................................................ 4
Product Support ....................................................... 4
Installation Instructions ............................................ 5
Before You Start .......................................................... 5
Tools Required............................................................. 5
Prepare Drill ................................................................. 5
Dismount SMV Reflector.......................................... 5
Update Clutch Shaft..................................................... 6
Install Small Seeds Clutch Sprocket ........................ 6
Seed Box Mounting...................................................... 7
Mark Holes for Drilling Box....................................... 7
Mount Small Seeds Box........................................... 8
Install Rate Adjuster..................................................... 9
Mount Adjuster Bracket............................................ 9
Mount Scale Plate .................................................... 9
Mount Adjuster Handle ............................................ 9
Align Adjuster Indicator ............................................ 9
Install Jackshaft Assembly......................................... 10
Install Chains ............................................................. 10
Meter Drive Chain .................................................. 10
Jackshaft Input Chain ............................................ 11
Shorten Chain for Seed-Only ............................. 11
Install Jackshaft Input Chain .............................. 11
Chain Alignment......................................................... 12
Fertilizer Drill Hoses ............................................... 13
Install Chain Guard .................................................... 13
Install Row Delivery Components .............................. 14
Hoses at Meters ..................................................... 14
Side Delivery Hardware ......................................... 14
Press Wheel Hose Delivery Hardware .................. 15
Walkboard Components ............................................ 16
Extend Walkboard ................................................. 16
Re-Mount SMV ...................................................... 16
Closeout .................................................................... 16
Operations................................................................ 17
Loading Seed ............................................................ 17
Small Seeds Box Loading...................................... 17
Small Seeds Rate...................................................... 17
Field Operations ........................................................ 17
Small Seeds Rate Calibration................................ 18
Small Seeds Row Shut-Off ................................ 20
Seed Rate ................................................................. 21
Maintenance............................................................. 23
Small Seeds Box Cleanout .................................... 23
Chain Maintenance.................................................... 23
Chain Slack............................................................ 23
Options ..................................................................... 25
Small Seed Tube Plugs ............................................. 25
Small Seed Removable Partition ............................... 25
Appendix .................................................................. 26
New Parts .................................................................. 26
Overall Kit .............................................................. 26
7-Foot Kits ............................................................. 27
10-Foot Kits ........................................................... 27
Seed Box Components.......................................... 28
Box Subassemblies ............................................... 29
Hardware Bundles ................................................. 31
Row Unit Components........................................... 32
Drive Bundles ........................................................ 33
Mount Hardware .................................................... 33
Small Seeds Jackshaft .......................................... 34
Jackshaft Subassembly ......................................... 35
Torque Values ........................................................... 36
Abbreviations............................................................. 37
Index ......................................................................... 39