CCI Thermal Technologies G Series - Industrial Infrared Gas Catalytic Heater - Manual (Page 6)

6
Separate Installation and Operation Instructions are available for industrial heating applications.
CAUTION
CONNECT BATTERY OUTSIDE 25 FT.
(7.6 M) IN NON-HAZARDOUS AREA.
9.0 SPOT HEATING
9.1 There are several factors to consider
when Cata-Dyne™ heaters are utilized for
spot heating.
9.2 Infrared energy travels in straight lines from
the face of the Cata-Dyne™ heater covering
approximately 160° of an arc and is inversely
proportional to the square of the distance.
The heater should therefore be mounted as
close as practical to the object requiring heat
for maximum temperature rise. A minimum of
28” (710 mm).
9.3 Match the shape of the object requiring heat
with the appropriate Cata-Dyne™ heater,
e.g. WX/BX 6 x 24 for long narrow objects or
WX/BX 12 x 12 for a square object.
9.4 Objects requiring heat should be painted dull,
dark colors for maximum infrared absorption
and objects not requiring heat should be
painted light or reflective colors.
9.5 Insulate and protect plastic, rubber and
similar materials from direct intense
infrared heat.
10.0 PERSONAL SAFETY
10.1 The Cata-Dyne™ flameless infrared catalytic
gas heater does not produce harmful carbon
monoxide gas when used with natural gas
or propane. Adequate ventilation must be
incorporated in any building design to ensure
oxygen replenishment and removal of any
carbon dioxide. Protective grills should be
used on any installation where personnel
may come in contact with the face of
the heater.
11.0 CLEANING
11.1 The Cata-Dyne™ heater box may be cleaned
but only once it has been allowed to cool. If
your Cata-Dyne™ catalytic pad (white pad) is
dirty it should never be contacted in order to
avoid damaging it. This means that it should
not be wiped down, sprayed with water or
blown with compressed air. Any contact with
the catalytic pad may damage the surface
requiring the owner to return the unit to the
factory for repair.
12.0 ORDERING INFORMATION
12.1 Quote requests can be made using our Online
RFQ process found at www.ccithermal.com.
12.2 Order any of CCI Thermal’s products by
telephone, fax, mail, e-mail or on-line at
www.ccithermal.com.
12.3 To assist us in processing your order as
quickly and efficiently as possible, please
provide us with the following information:
• Cata-Dyne™ product name
• Cata-Dyne™ model number
• Fuel gas - natural gas or propane
• Starting voltage - 12, 24, 120, 208, 240,
480 or 600V
• Accessories required:
– Protection Grill
– Wall Mount Brackets
– Thermostat
– Regulator
– Start Up Leads (12V system only)
– Vent Hood
– Other
• Company name and contact
• Billing address and phone number
• Shipping instructions
• Special tagging instructions
• Date required
• Method of payment:
– on account - P.O. number required
– credit card -
VISA or Mastercard number
– cash or cheque
13.0 REPAIRS
13.1 If the heater malfunctions, and is no longer
operating, send the heater to the factory for
servicing. Do not attempt to service the unit.
13.2 When returning the heater you can fill out the
online repair form at http://www.ccithermal.
com/online-repair-form.php or include the
following information with the heater
when shipping:
• Company name and address
• Contact name
• Telephone/fax number/email
• Product model and serial numbers
• Tagging codes
• Advise if an estimate is required prior to