Watts LLL100XL - Manual

For Water Heater Applications
ES-SL-100XL/L100XL/LL100XL/LLL100XL
Job Name ––––––––––––––––––––––––––––––––––––––––––– Contractor ––––––––––––––––––––––––––––––––––––––––––––
Job Location ––––––––––––––––––––––––––––––––––––––––– Approval –––––––––––––––––––––––––––––––––––––––––––––
Engineer ––––––––––––––––––––––––––––––––––––––––––––– Contractor’s P.O. No. ––––––––––––––––––––––––––––––––––
Approval ––––––––––––––––––––––––––––––––––––––––––––– Representative ––––––––––––––––––––––––––––––––––––––––
IMPORTANT: INQUIRE WITH GOVERNING AUTHORITIES
FOR LOCAL INSTALLATION REQUIREMENTS
Size 3 ⁄
4
" (20mm)
CSA Rated. Standard Models are self-closing T&P Relief Valves for Water
Heaters up to 105,000 BTU/Hr.
Watts Series SL100XL, L100XL , LL100XL and LLL100XL have extended
inlet shanks for use with the new generation of water heaters containing
extra thick insulation. These valves eliminate the use of an extension
nipple required with standard shank length models.
The combined 2-in-1 Temperature & Pressure relief valve provides the
least expensive and proven means for protection against both excessive
temperature and pressure emergency conditions.
Watts Self-closing combination T&P relief valves are design certified,
rated and listed by CSA to the requirements of ANSI Z21.22; and by the
National Board to the requirements of ASME Section IV.
They provide fully automatic temperature and pressure relief protection
for hot water storage tanks and heaters up to 105,000 BTU/Hr.
The temperature sensing element must be immersed in the water within
the top 6" (152mm) of the tank. Male inlet and female outlet. Temperature
relief 210°F (99°C). Standard setting 75, 100, 125, 150psi (5.3, 7.0, 8.8,
10.6 bar).
Features
• Model SL100XL Extended inlet model for installations with thick insula-
tion. Suitable for water heaters with up to 1 3 ⁄
4
" (44.5mm) of insulation.
• Model L100XL Extended inlet model for installations with thick insula-
tion. Suitable for water heaters with up to 2" (50.8mm) of insulation.
• Model LL100XL Extra extended inlet model. Suitable for water heaters
with up to 2 1 ⁄
2
" (63.5mm) of insulation.
• Model LLL100XL Extra extended inlet model. Suitable for water heaters
with up to 3" (76mm) of insulation.
• Thermostats with special protective coating.
• All bronze body.
• Stainless steel spring.
• Thermostat is accurate and proven. Exclusively designed and manufac-
tured by Watts.
Specifications
Temperature & Pressure Relief Valves
Each hot water storage heater shall be equipped with a CSA and ASME
rated automatic temperature and pressure relief valve to protect the
heater from excessive pressure and excessive temperature. The device
shall be design certified, rated and listed by CSA to the requirements of
ANSI Z21.22; and by the National Board to the requirements of ASME
Section IV. The BTU discharge capacity of the device shall be in excess
of the BTU input rating of the heater. Watts Series SL100XL, L100XL,
LL100XL or LLL100XL.
LLL100XL LL100XL L100XL SL100XL
Series SL100XL, L100XL,
LL100XL and LLL100XL
Extended Shank
Watts product specifications in U.S. customary units and metric are approximate and are provided for reference only. For precise measurements,
please contact Watts Technical Service. Watts reserves the right to change or modify product design, construction, specifications, or materials with-
out prior notice and without incurring any obligation to make such changes and modifications on Watts products previously or subsequently sold.
This device is designed for emergency safety relief and
shall not be used as an operating control.
NOTE: The information contained herein is not intended to
replace the full product installation and safety information
available or the experience of a trained product installer. You
are required to thoroughly read all installation instructions and
product safety information before beginning the installation of
this product.
WARNING !