CommScope PWR-COBRA-1 RET Antenna System User Manual
Page 4
Andrew,
A
CommScope
Company
3 Westbrook Corporate Center, Suite 900, Westchester, Illinois U.S.A. 60154
U.S.A.: +1 (800) 279-8185 • International: +1 (703) 726-5556
WWW.CommScope.Com
© 2008 CommScope
639568 • Revision C • November 2008
Page 4 of 6
15. After all the antenna actuators have been configured and the downtilt settings have been
adjusted to their new values, you may want to generate a record of your work. Go to the
AISG screen shown in Figure 2 to generate a record (a read only XML file will be
generated).
Double click on the serial number of the antenna actuator (on the Identification screen)
you want to create a record on, and then click on File located on the AISG tab screen.
The software will prompt you for the location you wish to store the file on your computer
and for a filename. Typically, the file is named after the site the antennas are installed on
(e.g. GA12345 or TX345). After saving this file, you will then return to the Identification
tab where you can repeat this process with the remaining antenna actuators listed. Each
time you click on File you will be asked Do you want to replace this, click Yes (this will
add the new serial number into the file and will start compiling a list.) Figure 3 shows an
example of a file generated using the process described in this step. These files (XML
format) can be opened/viewed through an Internet browser (Microsoft Internet Explorer).
-
<
Antenna
>
-
<
Settings ID
="
EM12033901DWDV
">
<
Field
Name
="
Date
"
Value
="
Wed, 12 Nov 2008 15:33:10 GMT
" />
<
Field
Name
="
Tilt
"
Value
="
2.0
" />
<
Field
Name
="
RET Software Version
"
Value
="
V2.3.1 [Build 02Nov07]
" />
<
Field
Name
="
Antenna Model
"
Value
="
RR6518VDPL2
" />
<
Field
Name
="
Antenna Serial Number
"
Value
="
E03287001294-1
" />
<
Field
Name
="
Antenna Frequency Bands
"
Value
="
16
" />
<
Field
Name
="
Antenna Beamwidth (1)
"
Value
="
65
" />
<
Field
Name
="
Antenna Beamwidth (2)
"
Value
="
0
" />
<
Field
Name
="
Antenna Beamwidth (3)
"
Value
="
0
" />
<
Field
Name
="
Antenna Gain (1)
"
Value
="
16.3
" />
<
Field
Name
="
Antenna Gain (2)
"
Value
="
0.0
" />
<
Field
Name
="
Antenna Gain (3)
"
Value
="
0.0
" />
<
Field
Name
="
Maximum Downtilt Angle
"
Value
="
7.0
" />
<
Field
Name
="
Minimum Downtilt Angle
"
Value
="
2.0
" />
<
Field
Name
="
Installation Date
"
Value
="
011207
" />
<
Field
Name
="
Installer Identifier
"
Value
="
00000
" />
<
Field
Name
="
Base Station Identifier
"
Value
="
BASE-STATION
" />
<
Field
Name
="
Sector Identifier
"
Value
="
Gamm
" />
<
Field
Name
="
Antenna Bearing
"
Value
="
0
" />
<
Field
Name
="
Installed Mechanical Tilt
"
Value
="
0.0
" />
<
Field
Name
="
Vendor Identifier
"
Value
="
EM
" />
<
Field
Name
="
Controller Model Number
"
Value
="
ACT_COBRA_3
" />
<
Field
Name
="
Controller Serial Number
"
Value
="
12033901DWDV
" />
<
Field
Name
="
Controller Identifier
"
Value
="
610198-3S
" />
<
Field
Name
="
RS-485 Termination
"
Value
="
false
" />
<
Field
Name
="
Number of Stepper Motors
"
Value
="
1
" />
<
Field
Name
="
Potentiometer Scaling
"
Value
="
612
" />
<
Field
Name
="
Shaft Gear
"
Value
="
40
" />
<
Field
Name
="
Stepper Motor Resolution
"
Value
="
200
" />
<
Field
Name
="
Worm Resolution
"
Value
="
1
" />
<
Field
Name
="
Number of Smoothing Samples
"
Value
="
8
" />
<
Field
Name
="
Left-Side Orientation
"
Value
="
false
" />
<
Field
Name
="
Calibration Current Limit
"
Value
="
290
" />