Connections, Connecting a composite video source to port 1, Connecting a s-video or video source to port 2 – Barco R9000901 User Manual
Page 12: Enter, Input selection, Adjust, Highlight 'picture tuning' and press, Select 'selected source' and press, Key. select 'random access' and press, 4 pin connector configurations
Connections
3-3
5975007 BARCOGRAPHICS 808S 051196
Connecting a Composite Video source to port 1.
Composite video signals from a VCR, OFF air signal decoder, etc..
PORT 4/5
See installation instructions b efore connecting to the supply.
Voir la not ice d'in stallat ion ava nt de r accorder au rés eau.
12 0/2 30 V
7/5 Amp
50/60 Hz
75 Ohm
PORT 2
7 5 Oh m
358
TV tuner, e.g. TVDM40 stereo
VCR
Audio amplifier
Composite
video
to next projector or
to a monitor
This device complies with part 15 of
the FCC rules. Operation is subject to
following two conditions (1). This
device may not cause harmful inter-
ference, and (2) this device must
accept any interference received
including interference that may cause
undesired operation"
Video input selection :
with the RCU or the build in RCU : press digit button 1
* Note : if using the loop-through Video output, then set the
Termination Switch to the "OFF" position.
Connecting a S-Video or Video source to port 2.
Separate Y-luma/C-chroma signals for higher quality playback of Super VHS signals.
Highlight Port 2 : Video and press ENTER to toggle between VIDEO
or S-VIDEO.
Press EXIT to return.
Press ADJUST to return to operational mode.
PORT 4/5
See installation instructions before connectin g to the supply.
Voir la no tice d' instal lation avant de rac corder au rés eau.
12 0/2 30 V
7/5 Amp
50/60 Hz
7 5 Oh m
PORT 2
7 5 Oh m
359
VCR S-VHS
Audio amplifier
Luma/Chroma
to next projector or
to a monitor
This device complies with part 15 of
the FCC rules. Operation is subject to
following two conditions (1). This
device may not cause harmful inter-
ference, and (2) this device must
accept any interference received
including interference that may cause
undesired operation"
Select with or
then
ADJUSTMENT MODE
Select a path from below :
GUIDED
RANDOM ACCESS
INSTALLATION
SERVICE
IRIS
Source 02
Select with or
then
Choose a setup pattern
from below :
SELECTED SOURCE
GENLOCKED PATTERN
INTERNAL # PATTERN
Source 02
Select with or
then
RANDOM ACCESS
ADJUSTMENT MODE
PICTURE TUNING
GEOMETRY
CONVERGENCE
FOCUSING
COLOR SELECT
ORBITING
CONTR. MODULATION
SOFT EDGE
Select with or
PICTURE TUNING
COLOR BALANCE
SYNC : FAST
PORT2 : S-VIDEO
LINE DOUBLER : ON
Highlight 'Picture Tuning' and press
ENTER
.
Select 'Selected source' and press
ENTER
.
Input selection
with the RCU or the build in RCU : press digit button 2
Depending on the priority setting in the Picture Tuning
menu, Video or S-Video can be displayed.
If the setting is not correct, start up the adjustment mode by
pushing on th
ADJUST
key.
Select 'Random Access' and press
ENTER
.
* Note: When using the Port 2 loop-through output, set the Termina-
tion Switch in the "OFF" position.
1
2
3
4
4 pin connector configurations:
For S-video:
Pin 1: earth(ground) luminance
Pin 2: earth(ground) chrominance
Pin 3: luminance signal(Y)
1Vpp
±
3dB
Pin 4: chrominance signal(C)
300mVpp
±
3dB
For video:
Pin 1: earth(ground) video
Pin 2: not connected
Pin 3: video signal
Pin 4: not connected