Balboa Water Group MLM990S - Manual (Page 11)

11
Heater Dry
Inadequate water detected in heater.
­ˆÃ«>ЮГКœ˜КМ ˆА`КœVVÕÀÀi˜ViʜvÊÌ iÊ
>LœÛiʓiÃÃ>}i°®Ê-«>КˆГКГ ХМК`œЬ˜°
1
/i“«iÀ>ÌÕÀiÊ՘Ž˜œÜ˜°
Temperature not current in Economy or
-ii«Ê“œ`i°
pH Low
pH is low.
pH High
pH is high.
Sanitizer Low
->˜ˆÌˆâiÀʈГКœЬ°
Sanitizer High
->˜ˆÌˆâiÀʈÃÊ ˆ} °
RTC Failure Hardware failure.
Persistent
Memory Fail
Hardware failure.
Checksum Failure ˆА“Ь>АiКˆ˜ГМ>К«АœLi“°
-ÞÃÌi“ÊVœ˜vˆ}ХАi`К
incorrectly. Menu
panel displays errors:
GFCI Failure
-«>КVœХ`ʘœМКМАˆ«К°
Stuck К«Х“«К>««i>АГКМœÊLiÊÃÌÕVŽÊœ˜]ÊV>ХГˆ˜}К
the water temperature to creep up,
possibly to hazardous levels.
К«Х“«К>««i>АГКМœК >ÛiÊLii˜ÊÃÌÕVŽКœ˜К
the last time spa was powered.
œœÜÊ>V̈œ˜ÊÀiµÕˆÀi`КvœАКМ iК>LœÛiʓiÃÃ>}i°Ê-«>КЬˆК˜œМК
automatically reset. Highlight and press
to reset.
vÌiÀÊÌ iК«Х“«К >ÃÊLii˜ÊÀ՘˜ˆ˜}КvœАК£К“ˆ˜ХМi]КМ iÊÌi“«iÀ>ÌÕÀiÊ܈Ê
be displayed.
˜Ê
Vœ˜œ“ЮКœАК-ii«Ê“œ`i]ÊÌ iК«Х“«К“>ÞÊLiʜvvÊvœАК œХАГКœХМГˆ`iК
a filter. If you wish to see the current spa temperature, either
Ã܈МV КМœК-М>˜`>А`К“œ`iКœАКМХА˜КiÌÃʣʜ˜КvœАК>Ìʏi>ГМК£К“ˆ˜ХМi°
``К«Кˆ˜VАi>ÃiÀÊ>VVœА`ˆ˜}КМœК“>˜Õv>VÌÕÀiÀ½Ãʈ˜ÃÌÀÕV̈œ˜Г°
``К«КАi`ÕViÀÊ>VVœА`ˆ˜}КМœК“>˜Õv>VÌÕÀiÀ½Ãʈ˜ÃÌÀÕV̈œ˜Г°
``КГ>˜ˆÌˆâiÀÊ>VVœА`ˆ˜}КМœК“>˜Õv>VÌÕÀiÀ½Ãʈ˜ÃÌÀÕV̈œ˜Ã°
,i“œÛiÊë>ÊVœÛiÀÊ>˜`Ê>œÜÊÃ>˜ˆÌˆâiÀÊ̜К`ˆГГˆ«>Мi°
œ˜М>VÌÊޜÕÀÊ`i>iÀʜÀÊÃiÀۈViКœА}>˜ˆâ>Мˆœ˜°
œ˜М>VÌÊޜÕÀÊ`i>iÀʜÀÊÃiÀۈViКœА}>˜ˆâ>Мˆœ˜КˆvК“iГГ>}iÊ>««i>АГКœ˜К
more than one power up.
œ˜Ì>VÌÊޜÕÀÊ`i>iÀʜÀÊÃiÀۈViКœА}>˜ˆâ>Мˆœ˜КˆvК“iГГ>}iÊ>««i>АГКœ˜К
more than one power up.
œ˜Ì>VÌÊޜÕÀÊ`i>iÀʜÀÊÃiÀۈViКœА}>˜ˆâ>Мˆœ˜
œ˜М>VÌÊޜÕÀÊ`i>iÀʜÀÊÃiÀۈViКœА}>˜ˆâ>Мˆœ˜°Кœ˜Мˆ˜Хi`Кœ«iА>Мˆœ˜К
may be unsafe.
*"7
,К"7 К-*К
/
9°К"К "/К
/
,К/
К7/
,°К
œ˜М>VÌÊޜÕÀÊ`i>iÀʜÀÊÃiÀۈViКœА}>˜ˆâ>Мˆœ˜
*"7
,К"7 К-*К
/
9°К"К "/К
/
,К/
К7/
,°К
œ˜М>VÌÊޜÕÀÊ`i>iÀʜÀÊÃiÀۈViКœА}>˜ˆâ>̈œ˜°
1 On some systems even when spa is shut down, some equipment may occasionally turn on to continue monitoring temperature
or if freeze protection is needed.
Configuration
Error
HOT -
Call Service
---°F or ---°C
---°F or ---°C
Configuration Error
Check Config. Settings
P 2.2 PS.1 ---
P 3.2
P 4.1 bL.1
---
---
P6.1
Diagnostic Messages
MESSAGE MEANING ACTION REQUIRED