Installation, Installation 13 – MTS Model 512-14 Hydraulic Power Unit User Manual
Page 13
512.14 Hydraulic Power Unit
Installation
13
Installation
This section describes how to install a Model 512.14 Hydraulic Power Unit.
Note
The HPU is designed for indoor use. The HPU should be stored and
installed indoors.
1. Position the hydraulic power unit.
Determine where to put the HPU. Since it is connected to the other
hydraulic equipment through hydraulic lines, the HPU can be located
remotely. Considerations include:
•
The air cooled HPU must be located where adequate air movement for
cooling can occur.
•
The water cooled HPU requires a source of water.
•
The HPU can be moved by a forklift, pallet jack or dolly.
•
The HPU produces 74 dB of sound pressure level in a free field acoustic
environment.
•
The base of the HPU has four holes that may be used to secure the unit in
place.
Connection Locations (Top View)
Drain Line Connection
Emergency Stop
Connection
Cooling Water In
Return Line Connection
Pressure Line Connection
Cooling Water Out
Water Valve
- Series 111 Accumulator (40 pages)
- Series 249G2 Swivels (34 pages)
- Series 201 Actuators (40 pages)
- Series 215 Rotary Actuator (68 pages)
- Series 242 Actuators (40 pages)
- Series 244 Actuators (68 pages)
- Series 247 Actuators (40 pages)
- Series 248 Actuators (46 pages)
- 709 Alignment System (158 pages)
- Series 609 Alignment Fixture (70 pages)
- 494 Controller Hardware FT 40 (344 pages)
- ReNew Technical Reference (50 pages)
- DCPD Measurement System (46 pages)
- Bionix EnviroBath (40 pages)
- FGW900 High-temperature Furnace (38 pages)
- Model 409.83 Temperature Controller (40 pages)
- Series 651 Environmental Chambers (30 pages)
- Series 653 High-Temperature Furnaces (38 pages)
- Series 658 Environmental Chamber (24 pages)
- Series FEC Environmental Chamber (48 pages)
- Model 685.53 Grip Control Module (24 pages)
- Series 685 Hydraulic Grip Supply (48 pages)
- Bend Fixture-10 kN (2 pages)
- Grip-Manual Bend Fixture-100 kN (2 pages)
- Grip-Manual Bollard-2 kN (2 pages)
- Grip-Manual Bollard-500 N (2 pages)
- Compression Platen-100 kN-100mm (2 pages)
- Compression Platen-100 kN-150mm (2 pages)
- Compression Platen-100 kN-200mm (2 pages)
- Compression Platen-20 kN (2 pages)
- Compression Platen-20 kN-100mm (2 pages)
- Compression Platen-20 kN-200mm (2 pages)
- Compression Platen-20 kN-SST (2 pages)
- Compression Platen-500 N FYC502A (2 pages)
- Compression Platen-500 N FYB502A (2 pages)
- Compression Platen-500 N-50mm (2 pages)
- Grip-Pneumatic Vise-Style-1 kN (2 pages)
- Pneumatic Bollard-500 N (2 pages)
- Scissor-Style-2 kN (2 pages)
- Scissor-Style-5 kN (2 pages)
- Screw-Style-5 kN (2 pages)
- Screw-Style-5 kN-SST (2 pages)
- Bend Fixture-1000 kN (2 pages)
- Bend Fixture-300 kN (2 pages)
- Bolt Grips (32 pages)