Koolance VID-290 - Manual

HD 2900 XT Thermal Pad Areas
NOTE: The VID-290 is designed for ATI Radeon HD 2900 XT cards. The video
card should be removed from the chassis in order to install this cooling device.
CAUTION: Removal of the original heat sink my void your manufac-
turer’s hardware warranty. Please consult the manufacturer if unsure,
and keep all original parts in case of a return/RMA.
!
VID-290 Installation Guide v 1.1
Most cards using the VID-290 are disassembled
the same way, although heat sink assemblies of
any given model can vary.
The rear GPU retention bracket and backplate screws should be removed fi rst (on
the video card’s bottom side). There should be about 12 of these on the video card.
There may also be heat sink mounting screws on the side of the L-bracket.
The heat sink and fan can now be carefully removed. Original thermal
paste may present additional resistance while removing the heat sink.
Unplug the heat sink fan wire. Remove the original RAM thermal transfer material,
and wipe any residual thermal material from the main GPU chipset.
Thermal paste is only required on the main GPU. The
other areas will utilize the included heat transfer pads.
Spread thermal compound on the GPU thinly and evenly
using the included paste packet, or a piece of thick paper
(such as a business card). Thermal paste is not required
on the surrounding metal support frame.
1 2
HD 2900 XT Disassembly Screws
Two sets of heat transfer pads are included, each with a
different thickness. The set allowing for best contact at the
GPU/chipset area should be used (check thermal paste
distribution after mounting). Transfer pads have plastic fi lm on
one or both sides that must be removed before application.
Place the heat transfer pads on each additional area of the
Koolance water block detailed below. (This includes 3 rows of
memory, 1 power/VReg area, and 1 small controller chip.)
Also
remove side
L-bracket
screws.
HD 2900 XT Thermal Pad Areas
NOTE: The VID-290 is designed for ATI Radeon HD 2900 XT cards. The video
card should be removed from the chassis in order to install this cooling device.
CAUTION: Removal of the original heat sink my void your manufac-
turer’s hardware warranty. Please consult the manufacturer if unsure,
and keep all original parts in case of a return/RMA.
!
VID-290 Installation Guide v 1.1
Most cards using the VID-290 are disassembled
the same way, although heat sink assemblies of
any given model can vary.
The rear GPU retention bracket and backplate screws should be removed fi rst (on
the video card’s bottom side). There should be about 12 of these on the video card.
There may also be heat sink mounting screws on the side of the L-bracket.
The heat sink and fan can now be carefully removed. Original thermal
paste may present additional resistance while removing the heat sink.
Unplug the heat sink fan wire. Remove the original RAM thermal transfer material,
and wipe any residual thermal material from the main GPU chipset.
Thermal paste is only required on the main GPU. The
other areas will utilize the included heat transfer pads.
Spread thermal compound on the GPU thinly and evenly
using the included paste packet, or a piece of thick paper
(such as a business card). Thermal paste is not required
on the surrounding metal support frame.
1 2
HD 2900 XT Disassembly Screws
Two sets of heat transfer pads are included, each with a
different thickness. The set allowing for best contact at the
GPU/chipset area should be used (check thermal paste
distribution after mounting). Transfer pads have plastic fi lm on
one or both sides that must be removed before application.
Place the heat transfer pads on each additional area of the
Koolance water block detailed below. (This includes 3 rows of
memory, 1 power/VReg area, and 1 small controller chip.)
Also
remove side
L-bracket
screws.