JUMO 709061 TYA 201 - Single-Phase Power Controller Data Sheet - Manual (Page 2)

2012-12-31/00561067
Data sheet 709061 Page 2/21
JUMO GmbH & Co. KG
Delivery address: Mackenrodtstraße 14
36039 Fulda, Germany
Postal address: 36035 Fulda, Germany
Phone: +49 661 6003-0
Fax: +49 661 6003-607
E-mail: [email protected]
Internet: www.jumo.net
JUMO Instrument Co. Ltd.
JUMO House
Temple Bank, Riverway
Harlow, Essex CM20 2DY, UK
Phone: +44 1279 635533
Fax:
+44 1279 635262
E-mail: [email protected]
Internet: www.jumo.co.uk
JUMO Process Control, Inc.
6733 Myers Road
East Syracuse, NY 13057, USA
Phone: 315-437-5866
1-800-554-5866
Fax: 315-437-5860
E-mail: [email protected]
Internet: www.jumousa.com
Technical data
Voltage supply, load current
Analog inputs
Binary inputs
Binary outputs, actual value output
Code Voltage supply for control electronics = max. load voltage Fan specifications
Type 709061/X-0X-250...
024 AC 24V -20%...+15%, 45 ...63 Hz AC 24V/30VA
042 AC 42V -20%...+15%, 45 ...63 Hz AC 24V/30VA
115 AC 115V -20%...+15%, 45 ...63 Hz AC 115V/30VA
230 AC 230V -20%...+15%, 45 ...63 Hz AC 230V/30VA
265 AC 265V -20%...+15%, 45 ...63 Hz AC 230V/30VA
400 AC 400V -20%...+15%, 45 ...63 Hz AC 230V/30VA
460 AC 460V -20%...+15%, 45 ...63 Hz AC 230V/30VA
500 AC 500V -20%...+15%, 45 ...63 Hz AC 230V/30VA
Load current I
L rms
AC 20, 32, 50, 100, 150, 200, 250A
Load type Resistive and resistive/inductive loads
Control section power consumption max. 20 VA
Control signal 0(4) … 20mA R
i
= 50
Ω
0(2) … 10V R
i
= 25k
Ω
0(1) … 5V R
i
= 25k
Ω
Default set point
value Via standard signals (current, voltage) or interface
Base load: Output as minimum control value
Maximum control value: Output as maximum control value
Example
P control:
Binary input 1, 2 For connection to potential-free contact or optocoupler, voltage proof up to DC 12V
Relay (changeover contact)
without contact suppression 150000 switching actions at a contact rating of 3A/230V 50Hz (resistive load)
Optocoupler output I
Cmax
= 2mA, U
CEOmax
= 32V
Actual value output Switched off as standard.
For standard signal, voltage: 0 … 10V , 2 … 10V, 0 … 5V to 1 … 5V
For standard signal,
current: 0 … 20mA to 4 … 20mA (burden max. 500
Ω)
Depending on the device type, the output of various internal measuring values such as load current, load
voltage or power is possible.
Thyristor firing re-
quest: setpoint specification
Current input
(current proof up to 25mA) setpoint specification
Voltage input
(voltage proof up to DC 32V) setpoint specification
Binary input1, 2
(voltage proof up to DC 32V) via Interface
continous The power controller provides the power for the load conti-
nuously depending on the default setpoint value. - possible
logic
(Solid State Relais
SSR) The power controller acts like a switch and provides the power
by either switching ON or OFF. The switching level is always in
the middle of the selected input range.
At 4 to 20mA it is 12mA, at 0 to 10V it is 5V. OFF logic level „0“ = 0 to +0,8V;
ON logic level 1 = +2 to 3,3V possible
Control signal
P
Base load: 680 W
Maximum
Output level: 3680 W
0 mA 20 mA
3000W 0...20mA ־
Base load