Intelix AVO-V3AD - Manual

© Intelix LLC www.intelix.com
Technical Specifications
Bandwidth Video: 60 MHz, 3 dB roll off
Digital audio: 25 MHz, 1dB roll off
Maximum Input 1.1Vp-p
Insertion Loss (video) .1 dB for 0.1 MHz. Gradually increasing to 2.5 dB over the
frequency range
Insertion Loss (audio) Less than 1 dB over the frequency range
Return Loss (video) Greater than 15 dB over the frequency range
Return Loss (audio) Greater than 15 dB over the frequency range
Common Mode Rejection
(video) -55 dB at 0.1MHz. Gradually increasing to –20 dB at 60 MHz
Common Mode Rejection
(audio) -50 dB at 0.1MHz. Gradually increasing to –30 dB at 25 MHz
Max. Distance Digital audio only: 600 feet
480i/p video only: 1,000 feet
480i/p video with digital audio: 600 feet
720p video only: 500 feet
720p video with digital audio: 500 feet
1080i/p video only: 500 feet
1080i/p video with digital audio: 500 feet
Cable – Cat5 UTP/STP
24 gauge or lower solid copper twisted pair wire impedance: 100
ohms at 1 MHz. Maximum capacitance: 20 pf/foot.
Attenuation: 6.6 dB/1000 ft at 1 MHz
Cable – Coax Impedance: 75 ohms at 1 MHz
Connectors Three (3) female RCA for Green (Y), Blue (Pb), and Red (Pr)
One (1) female RCA for digital audio
One (1) Shielded RJ45 for twisted pair
Pin Configuration
Reverse polarity sensitive Red (Pr): Pins 7 & 8
Green (Y): Pins 3 & 6
Blue (Pb): Pins 1 & 2
Digital Audio: Pins 4 & 5
Temperature Operating: 0° to 55°C
Storage: -20° to 85°C
Humidity: up to 95%
Enclosure ABS fire retardant plastic
Dimensions 4.3” x 2.5” x 1.0”
Weight 0.2 lbs.
Regulatory FCC, CE
Warranty 2 years
Order Information AVO-V3AD, AVO-V3AD-PAC
Intelix LLC
2222 Pleasant View Road
Phone: 608-831-0880
Suite #1 Fax: 608-831-1833
Middleton, WI 53562 Toll-Free: 866-4-MATMIX
www.intelix.com [email protected]
Intelix AVO-V3AD HDTV Component Video and
Digital Audio Balun Installation Guide
Introduction
The Intelix AVO-V3AD component video and digital audio HDTV balun
transmits a YPbPr (RGB) signal and digital audio over inexpensive structured
pair cabling, such as Cat 5.
Used in pairs, the AVO-V3AD supports 480i/p, 720p and 1080i/p resolutions for
hi-definition multimedia applications.
Installation
One (1) pair of baluns is needed to
complete one component (YPbPr) or
RGB connection via Cat5 twisted
pair. To install the baluns, perform
the following steps:
1. Identify the pin configuration of
the baluns. Three (3) twisted
pairs are required for video and
one (1) twisted pair is required
for digital audio. The pin
configuration follows the
EIA/TIA 568A/B standard. The
Intelix AVO-V3AD balun is
reverse polarity sensitive. Please
ensure that wiring is straight-
through.
2. Connect one AVO-V3AD balun
to the component video coaxial
cable output of the video source using three RCA video cables. Ensure the
color codes of the AVO-V3AD and video equipment match.
3. Connect a second AVO-V3AD balun to the component video coaxial cable
input of the receiver(s) at the remote end using three RCA video cables.
4. Complete the connection between the two baluns using standard Cat 5 twisted
pair cable. Verify the Cat 5 is terminated with RJ45 connectors on both ends.
Ensure that there are no split pairs or taps.