Intelix AVO-V1-PAIR-F - Manual

Specifications
Specifications subject to change without notice.
Maximum Distance*
2200 feet
Maximum Video Input 1.1 Vp-p
Bandwidth (video) DC to 8 MHz
Impedance (video) 75 ohms
Insertion Loss Less than 2 dB per pair over the frequency range from
DC to 8 MHz
Return Loss Greater than 15 dB over the frequency range from DC to
8 MHz
Common Mode Rejection Greater than 40 dB @ 8 MHz
Unshielded Twisted Pair Maximum capacitance: 20 pf/foot
Cabling Specifications Impedance: 100 ohms @ 1 MHz
(24 gauge or lower solid Attenuation: 6.6 dB/1000 ft. @ 1 MHz
copper) Cat 3, Cat 5, Cat 5e, Cat 6, Cat 7 compatible
Connectors One (1) male BNC to one (1) RJ45
Pinout 7 & 8, pair 4
Temperature Operating: 32 to 131 F (0 to 55 C)
Storage: -4 to 185 F (-20 to 85 C)
Humidity: up to 95%
Enclosure Black plastic
Dimensions 1.6” x 2.8” x 1”
Ordering Information AVO-V1: single AVO-V1 balun in bulk packaging
AVO-V1-PAC: two AVO-V1 baluns in retail-ready
packaging
Warranty 2 years
* Distances and picture quality may be affected by cable grade, cable quality, source and
destination equipment, RF and electrical interference, and cable patches. Intelix specifications are
based on straight-through cabling with standard-grade Cat 5.
Contact Information
Intelix
2222 Pleasant View Road
Middleton, WI 53562
Toll-free: 866-4-MATMIX
Phone: 608-831-0880
Fax: 608-831-1833
www.intelix.com
Intelix AVO-V1 Video Balun
Ins Ins Ins Ins Inst tt ttallation Manual allation Manual allation Manual allation Manual allation Manual
The Intelix AVO-V1 video balun eliminates 75-ohm
coaxial cable and allows composite baseband video
to be transmitted via a single unshielded twisted pair
(UTP) cable, such as Cat 5. Typically, AVO-V1
baluns are used in pairs to transmit standard NTSC,
PAL, or SECAM composite video.
The AVO-V1 is used with video equipment, as well
as CCTV security and surveillance equipment, such
as CCTV cameras, monitors, DVRs, video
sequencers, video multiplexers, quads, video switchers, CCTV camera servers, and VCRs.
To install an AVO-V1 balun, perform the following steps:
1. Turn off power and disconnect the video equipment by following the manufacturer’s
instructions.
2. Run your unshielded twisted pair cabling, such as Cat 5. One twisted pair is
required for each camera signal.
3. The AVO-V1 balun works in pairs. Plug one AVO-V1 balun into the BNC
connector of the source device.
4. Plug a second balun into the BNC connector of the destination equipment at the
other end of the cable.
5. Connect a structured cable, such as Cat 5, to each RJ45 connector of the baluns.
Verify the pinout on the connector conforms to the EIA/TIA 568A or 568B pattern.
6. Power-on the video equipment and check the picture quality. The video should be
clear and sharp within the maximum specified distances.
Installation
Caution: Do not attempt to open the balun housing. There are no user-serviceable parts
inside the AVO-V1. Opening the unit will void your warranty.
Caution: Do not connect the AVO-V1-ST to a telecommunication outlet wired to
unrelated equipment. Making such a connection may damage the equipment
and/or balun. Please ensure all wiring is “straight-through.”
Caution: Do not mount the balun over equipment ventilation openings. Covering the
openings may cause the equipment to overheat.
AvoCat
Series