Enerpac CT-604 - Manual

1
POWERFUL SOLUTIONS. GLOBAL FORCE.
L2755 Rev. C 02/11
CT-604 Hydraulic Coupler Bleed Tool
Instruction Sheet
1.0 IMPORTANT RECEIVING
INSTRUCTIONS
Visually inspect all components for shipping damage.
Shipping damage is not covered by warranty. If ship-
ping damage is found, notify carrier at once. The car-
rier is responsible for all repair and replacement costs
resulting from damage in shipment.
2.0 INTENDED USE
The Enerpac CT-604 coupler bleed tool is designed to
safely relieve pressure from hydraulically locked high-
fl ow hydraulic couplers, Enerpac coupler models CH-
604 (male half), CR-400 (female half) and C-604 (male
and female set).
3.0 SAFETY ISSUES
Read all instructions, warnings and
cautions carefully. Follow all safety
precautions to avoid personal injury or
property damage during system operation. Enerpac
cannot be responsible for damage or injury resulting
from unsafe product use, lack of maintenance or
incorrect product and/or system operation. Contact
Enerpac when in doubt as to the safety precautions
and operations. If you have never been trained on
high-pressure hydraulic safety, consult your
distribution or service center for a free Enerpac
Hydraulic safety course.
Failure to comply with the following cautions and
warnings could cause equipment damage and
personal injury.
A CAUTION is used to indicate correct operating or
maintenance procedures and practices to prevent
damage to, or destruction of equipment or other
property.
A WARNING indicates a potential danger that requires
correct procedures or practices to avoid personal
injury.
A DANGER is only used when your action or lack of
action may cause serious injury or even death.
WARNING: Wear proper personal
protective gear when operating hydraulic
equipment.
Never set the relief valve to a higher pressure
than the maximum rated pressure of the pump.
Higher settings may result in equipment
damage and/or personal injury.
WARNING: The system operating pressure
must not exceed the pressure rating of the
lowest rated component in the system.
Install pressure gauges in the system to
monitor operating pressure. It is your window to what
is happening in the system.
CAUTION: Avoid damaging hydraulic
hose. Avoid sharp bends and kinks when
routing hydraulic hoses. Using a bent or
kinked hose will cause severe back-pressure. Sharp
bends and kinks will internally damage the hose
leading to premature hose failure.
Do not drop heavy objects on hose. A
sharp impact may cause internal damage
to hose wire strands. Applying pressure to
a damaged hose may cause it to rupture.
DANGER: Do not handle pressurized
hoses. Escaping oil under pressure can
penetrate the skin, causing serious injury. If
oil is injected under the skin, see a doctor immediately.
IMPORTANT: Hydraulic equipment must
only be serviced by a qualifi ed hydraulic
technician. For repair service, contact the
Authorized ENERPAC Service Center in
your area. To protect your warranty, use only ENERPAC
oil.
WARNING: Immediately replace worn or
damaged parts with genuine ENERPAC
parts. Standard grade parts will break
causing personal injury and property
damage. ENERPAC parts are designed to fi t properly
and withstand high loads.
Index:
English . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Français . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Deutsch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
Italiano . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-8
Español . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-10
Nederlands . . . . . . . . . . . . . . . . . . . . . . . . . . 11-12
Portuguese . . . . . . . . . . . . . . . . . . . . . . . . . . 13-14
Finnish . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-16
Norwegian . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-18
Swedish. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-20
中文 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-22
日本語 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-24