AMMCO 1350 Brake Washer Systems - Manual (Page 4)

ASSEMBLY
MODEL 1450 DELUXE BRAKE WASHER
1. Turn base and barrel assembly upside down.
2. Align caster bracket holes with holes in base.
3. Use the 5 ⁄
16
" screws and nuts to attach casters to
base.
4. Turn base and barrel assembly right side up.
5. Attach water filter bracket to outside of barrel
using 1 ⁄
4
" screws, washers, and nuts. Make sure
washers are on the inside of the barrel.
6. Insert pick-up hose through hole in the side of the
barrel and screw strainer onto fitting.
7. Lay the oil boom in the bottom of the barrel.
8. Position the pan and lid assembly on top of the
barrel so that the pump will be above the water fil-
ter.
9. Expand the locking ring to allow the lid to seat to
the top of the barrel. Then tighten ring with the
cam lever.
10. Fasten the pump and air filter/regulator to the pan
with the #10 screws, washers, and nuts. Make
sure the washers are on the inside of the pan.
11. Connect water filter outlet hose to pump
“IN” port. Slide lever to lock in place.
12. Unscrew water filter canister and insert
filter cartridge. Hand tighten canister.
13. Fill tank to 10 gallon on barrel with
water only.
14. Pour one quart of AMMCO cleaner into
the barrel.
NOTE: DO NOT USE GASOLINE OR
FLAMMABLE SOLVENTS IN THIS
BRAKE WASHER. USE ONLY
ORIGINAL AMMCO PRODUCTS
FOR YOUR SAFETY AND TO
ENSURE COMPLIANCE TO
O.S.H.A. REGULATIONS.
15. Insert filter sock into pan drain hole and
place drain grate on top of sock.
16. Add quick connector fitting to washer air inlet
hose.
17. Connect “Y” hose assembly to pump “OUT” port.
Slide lever to lock in place.
18. Insert (2) long hose ends of “Y” assembly through
holes in side of pan assembly.
19. Screw gun assemblies on the ends of “Y” hose
assembly.
20. Place parts basket over side of pan.
21. Write date on service sticker and apply to a conve-
nient location on washer.
ASSEMBLY
MODEL 1350 PORTABLE BRAKE WASHER
1. Fasten the pump and air filter/regulator to the pan
with the #10 screws, washers, and nuts. Make
sure the washers are on the inside of the pan.
2. Screw pick-up hose/strainer assembly into bulk-
head fitting on the inside of pan.
3. Screw hose assembly into outside of bulk-head fit-
ting. Connect other end to pump “IN” port. Slide
lever to lock in place.
4. Place filter filler in center depression of pan.
5. Lay filter mat in bottom of pan, smooth side up.
6. Pour 3 gallons of water only into pan.
7. Pour 1⁄3 bottle of AMMCO cleaner in pan.
NOTE: DO NOT USE GASOLINE OR
FLAMMABLE SOLVENTS IN
THIS BRAKE WASHER. USE
ONLY ORIGINAL AMMCO
PRODUCTS FOR YOUR
SAFETY AND TO ENSURE
COMPLIANCE TO O.S.H.A.
REGULATIONS.
8. Add quick connector fitting to
washer air inlet hose.
9. Connect “Y” hose assembly to
pump “OUT” port. Slide lever to
lock in place.
10. Insert (2) long hose ends of “Y”
assembly through holes in side
of part assembly.
11. Screw gun assembly on the ends
of “Y” hose assembly.
12. Place parts basket over side of pan.
13. Write date on service sticker and apply to a conve-
nient location on washer.
2 • AMMCO 1350/1450 Brake Washer Systems
WARNING
Do not use gaso-
line or flammable
solvents.
Explosion and
Fire hazard.