2N Fixed line replacement with 2N EasyGate PRO - Quick Start, 1711 v1.01 - Manual (Page 2)

2N® EasyGate Pro Quick Start
Basic Functions
· The primary purpose of 2N® EasyGate Pro
(from now only ‘Easy Gate’) is to transmit
voice between a GSM network and an
attached FXO-interface terminal.
· You can establish data connections (GPRS,
CSD) and send/receive SMS in combination
with a PC.
· Models of EasyGate with fax converter can
transmit fax messages using analog fax
Group 3 or data using analog modem on
telephone line
· You can send an SMS to a pre-
programmed number using the SMS
sending input.
· The battery backed-up EasyGate version
allows you to maintain your traffic even in
the event of power outage.
· Firmware for EasyGate can be updated
from www.2n.cz
Read the CD-ROM User Manual carefully to get familiar with all system
functions.
EasyGate supports GSM GPRS technology for data connection. The
connection speed and quality depend on the GSM provider, accessible
services, signal coverage and network status.
2N® EasyGate Pro Installation and Connection
· Proper Location
- Install EasyGate with respect to a good
GSM signal strength.
- Place EasyGate out of range of sensitive
devices and human bodies for
electromagnetic interference reasons.
- EasyGate is designed for indoor use. Do
not place it near heat sources and on
direct solar radiation. It may not be
exposed to rain, flowing water and
moisture, aggressive gas, solvents etc.
· Needed Accessories
INCLUDED IN THE BOX
· 1x 2N® EasyGate PRO device
· 1x power adapter (12V/0,5A DC)
· 1x magnetic antenna with cable (SMA)
· 1x antenna for direct connection (SMA)
· 1x PC-connection USB A/B cable
· 1x telephone cable
· 1x SMS sending input connector
· 2x screws with dowels
· 1x CD with manual and SW
· 1x Quick Start manual
NOT INCLUDED IN THE BOX
· SIM card
· Information on Internet connection from
your provider (APN etc.)
· Rechargeable batteries
· External Antenna Connection
Screw the antenna cord into the SMA
antenna
connector. Tighten the
antenna connector gently with your
hand, never use a wrench!
· SIM Card Installation
Slot for SIM card is placed on the
connector panel. Insert the SIM card to
the slot according to the picture and
make sure that the card is locked
properly. Select the required GSM
provider and SIM card services, such as
call forwarding, call barring, preferred
networks, SMS centre, etc. using your
mobile phone before inserting your SIM
card into EasyGate.
· Telephone Line Connection
EasyGate can be connected to any
FXO-interface equipment (standard
telephone set, answering machine, PBX
CO line...). EasyGate is equipped with
identification of calling party (CLIP) via
FSK and so it is advantageous to connect
a terminal that is able to display the CLI.
· Battery installation (battery
backup type)
Insert four pieces of rechargeable
battery NiMh size AA into the covered
compartment on the back side of the
gateway. Refer to the compartment
label for proper battery placement and
polarity. Use mentioned type of
batteries only!
· Mains Supply Connection and
Switch On
EasyGate is 12V DC voltage powered.
Connect the attached power adapter
(12V/0,5A DC) to the power supply
connector. After connection, switch on
EasyGate with the power switch on the
right-hand side of connector panel.
Do not activate the power supply until the antenna is connected to
EasyGate to avoid the GSM module damage.
2N® EasyGate Pro Connection Layout
Detailed description is in manual on CD-ROM
PIN Secured SIM Card
1. Hook off the telephone and hear the
PIN tone:
2. Enter the PIN using DTMF and press
for confirmation. Hang up the line to
cancel a wrong PIN.
3. If you hear the busy tone after a while
(a few seconds), the PIN has been
entered correctly. This PIN will be
entered automatically upon every
power up.
4. If you hear the PIN tone again after a
while, the PIN has not been entered
correctly. Re-enter the PIN.
By entering three wrong PINs you block the SIM card. Enter the PUK code
into your mobile phone to unblock the SIM card.
Indication LEDs
Power
supply
Blue light – mains supply
Yellow light – battery supply
GSM
Network
Blue flashes – logged out
Blue light – logged in
Phone
line
No light – standby
Yellow flashes quickly – ringing
– line off-hook
Yellow light – call
Flashes 2-3 times – fax or data
connection over FXS (fax version)
Data
Green light – PC connected
Flashes quickly – incoming data
1x in 3s – data transmission
Signal,
battery
indicator
Signal strength indicator
After hook off before start of dialing
– battery state
Power adapter
IN: 110V/240V AC
OUT: 12V/0.5A DC
Analog phone
(FXO interface device)
SIM
PC (USB)
SMS
input
Switch ON/OFF
(Backed-up version only)