Echo 76624 Owners Manual v.3 - Manual (Page 9)

7 6 INCH CHIPPER
SAFETY
See Section 1.9 for decal locations. Familiarize yourself with all of the safety and operating decals on the machine and
the associated hazards. See the engine owners manual for engine safety instructions and decals. Make certain that
all safety and operational decals on this machine are kept clean and in good condition. Refer to the parts catalog if you
need a replacement decal. decals that need replacement must be applied to their original locations.
1.11 safeTY decals
9
Pn 14942-00
3
Pn 12173
do Not oPeRate thIS
eQuIPMeNt IN the vICIN-
Ity oF byStaNdeRS. do
Not alloW ChIldReN to
oPeRate thIS eQuIPMeNt.
alWayS StaNd CleaR oF
dISChaRGe aRea WheN
oPeRatING thIS MaChINe.
keeP FaCe aNd body aWay
FRoM dISChaRGe aReaS.
Read aNd uNdeRStaNd the
oWNeR/oPeRatoRS MaNu-
al. be CoMPletely FaMIl-
IaR WIth the CoNtRolS aNd
PRoPeR uSe oF thIS eQuIP-
MeNt.
Pn 13711-00
7
1
Pn 12169
keeP haNdS aNd Feet out oF INlet aNd
dISChaRGe oPeNINGS WhIle Ma-
ChINe IS oPeRatING to avoId Se-
RIouS PeRSoNal INjuRy. StoP
aNd alloW MaChINe to CoMe to a
CoMPlete StoP beFoRe CleaRING
obStRuCtIoNS.
2
Read aNd uNdeRStaNd thIS
oWNeR/oPeRatoRS MaNual.
be CoMPletely FaMIlIaR WIth
the CoNtRolS aNd the PRoP-
eR uSe oF thIS eQuIPMeNt
obtaIN aNd WeaR SaFety GlaSS-
eS aNd uSe heaRING PRoteC-
tIoN at all tIMeS WheN oPeRat-
ING thIS MaChINe.
beFoRe INSPeCtING oR SeRvIC-
ING aNy PaRt oF thIS MaChINe,
Shut oFF PoWeR SouRCe, dIS-
CoNNeCt SPaRk PluG WIRe
FRoM SPaRk PluG aNd Make
SuRe all MovING PaRtS have
CoMe to a CoMPlete StoP.
Pn 12172
CheCk blade boltS FoR
PRoPeR toRQue aFteR
eveRy 8 houRS oF oPeRa-
tIoN. CheCk bladeS aNd
Rotate oR ReShaRPeN
daIly oR aS ReQuIRed to
keeP bladeS ShaRP. Re-
FeR to oWNeRS MaNual FoR INStRuCtIoNS. FaIluRe to
do So May CauSe PooR PeRFoRMaNCe, daMaGe oR PeR-
SoNal INjuRy aNd WIll voId the MaChINe WaRRaNty.
Pn 12250 6
Pn 12174
4
do Not oPeRate MaChINe WIth-
out ShIeldS IN PlaCe. FaIluRe to
do So May CauSe SeRIouS INjuRy
oR death.
8
Pn 18983-00
Feed RolleR SuPPoRt
MuSt be SeCuRed IN
the uP PoSItIoN PRIoR
to SeRvICING ChIPPeR
Feed aRea. the Feed
RolleR CaN Fall aNd
CauSe SeveRe bodIly
haRM. CoNSult oWNeRS MaNual FoR PRoPeR Method
oF SeCuRING Feed RolleR SuPPoRt. loWeR Feed Roll-
eR beFoRe oPeRatING ChIPPeR.
Pn 12175
5
keeP haNdS aNd Feet out
oF INlet aNd dISChaRGe
oPeNINGS WhIle MaChINe
IS oPeRatING to avoId SeRI-
ouS PeRSoNal INjuRy. alloW
MaChINe to CoMe to a CoM-
Plete StoP beFoRe CleaR-
ING obStRuCtIoNS.