beautypg.com

4 operation safety, 5 pto safety, 4 operation safety 1.5 pto safety – Echo 73413 Owners Manual v.3 User Manual

Page 6

background image

4 INCH CHIPPER

2

SAFETY

Shut off the machine and make sure all moving parts

have come to a complete stop before inspecting or

servicing any part of the machine. Disconnect the

battery and remove the ignition key if applicable.

7. do not insert branches with a diameter larger than

the max chipper capacity into machine or machine

damage may occur.

8. When feeding material into machine, do not allow

metal, rocks, bottles, cans or any other foreign material

to be fed into the machine.

9. Ensure debris does not blow into traffic, parked cars,

or pedestrians.

10. keep the machine clear of debris and

other accumulations.

11. do not allow processed material to

build up in the discharge area. this

may prevent proper discharge and

can result in kickback of material

through the feed opening.

12. If the machine becomes clogged, the cutting

mechanism strikes any foreign object, or the machine

starts vibrating or making an unusual noise, shut off

machine immediately and make sure all moving parts

have come to a complete stop. Disconnect the battery

and remove the ignition key if applicable. After the

machine stops: A) Inspect for damage, B) Replace

or repair any damaged parts, and C) Check for and

tighten any loose parts.

13. On electric start models, disconnect cables from battery

before doing any inspection or service. Remove key.

14. Check blade bolts for proper torque after every 8 hours

of operation. Check blades and rotate or resharpen

daily or as required to keep blades sharp. Failure to do

so may cause poor performance, damage or personal

injury and will void the machine warranty.

1. Always stand clear of discharge area when operating

this machine. keep face and body away from feed

and discharge openings.

2. keep hands and feet out of feed and

discharge openings while machine is

operating to avoid serious personal

injury. Stop and allow machine to

come to a complete stop before

clearing obstructions.

3. Set up your work site so you are not endangering traffic

and the public. Take great care to provide adequate

warnings.

4. Do not climb on machine when operating. keep proper

balance and footing at all times.

5. Check cutting chamber to verify it is empty before

starting the machine.

6. The disk will continue to rotate after being disengaged.

or ill. You must be in good health to operate this

machine safely.

7. Do not operate this equipment in the vicinity of

bystanders. keep the area of operation clear of all

persons, particularly small children. It is recommended

that bystanders keep at least 50 feet (15 meters) away

from the area of operation.

8. Do not allow children to operate this equipment.
9. use only in daylight or good artificial light.
10. Do not run this equipment in an enclosed area. Engine

exhaust contains carbon monoxide gas, a deadly

poison that is odorless, colorless and tasteless. Do not

operate this equipment in or near buildings, windows

or air conditioners.

11. Always use an approved fuel container. Do not

remove gas cap or add fuel when engine is running.

Add fuel to a cool engine only.

12. Do not fill fuel tank indoors. keep open flames, sparks,

smoking materials and other sources of combustion

away from fuel.

13. do not operate machine without shields in place.

Failure to do so may cause serious injury or death.

14. keep all guards, deflectors, and shields in good

working condition.

15. Before inspecting or servicing any part of this machine,

shut off the machine and make sure all moving parts

have come to a complete stop. Disconnect the battery

and remove the ignition key where applicable.

16. Check that all screws, nuts, bolts, and other fasteners

are secured, tightened and in proper working condition

before starting the machine.

17. do not transport or move machine while it is operating

or running.

1.4 opERaTIoN SaFETY

1.5 pTo SaFETY

1. Read and follow instructions on PTO safety decals.
2. Stay alert and pay attention when PTO is operating.
3. keep bystanders, especially children, away from PTO

driveline.

4. Check the driveline to ensure it is attached securely

to the power supply.

5. keep guards and shields in place at all times while

operating. Disengage PTO, shut off power source, and

make sure all moving parts have come to a complete

stop before removing guards or shields.

6. Clothing worn by operator must be fairly tight. Never

wear loose fitted jackets, shirts, or pants when working

around the pto. tie long hair back or put under a

cap.

7. keep hydraulic hoses, electric cords, chains and other

items from contacting the driveline.

This manual is related to the following products: