Synergy 8072-03 - JK Weld-On Rear Upper Control Arm Bracket User Manual
Synergy For the car
SYNERGY MFG. 870 INDUSTRIAL WAY, SAN LUIS OBISPO, CA (805) 242-0397
INSTALLATION INSTRUCTIONS
PPM-8072-03 JK REAR UPPER CONTROL
ARM BRACKET
GENERAL NOTES:
• These instructions are also available on our website at www.synergymfg.com
Check the website for any updated instructions and additional photos for
reference.
• This is a weld on bracket and should be installed by an experienced welder.
• We recommend installing one side at a time as to not disrupt pinion angle or
suspension geometry.
INSTRUCTIONS:
1) It is easiest to install these brackets with the suspension sitting at ride height on
jack stands and to remove the following components.
Remove the rear wheels and tires
Remove the rear axle and rear brake assy.
Also remove rear bump stop spacers (if any)
Remove one upper control arm at a time for installation.
2) Begin by removing the stock upper control arm bracket. The bracket is easiest to
remove in 2 pieces. First, make 2 cuts at the top of the welds and one cut down
the side of the stock bracket as shown.
- 3427 - Univ Jeep Shock Stem Adapter (1 page)
- 4012 - Jeep JK Spare Tire Relocation Bracket (1 page)
- 4018 - Jeep JK Compressor Mount (3 pages)
- 4018-RHD - JK Onboard Air Compressor Bracket RHD (Viair & ARB) (4 pages)
- 4024 - Jeep JK Air Tank Mount (2 pages)
- 4034 - Air Compressor Bracket 12+ JK w/ 3.6L Pentastar (4 pages)
- 4040 - Synergy Sit Shower Shave Kit (21 pages)
- 4105 / 6 - D60 Drive Gears (1 page)
- 4120 Series - Heavy Duty Ball Joints (1 page)
- 4121/21-01 - Heavy Duty Ball Joints (1 page)
- 4122/22-01 - Heavy Duty Ball Joints (1 page)
- 4124 - Heavy Duty Ball Joints (2 pages)
- 4125 - HD Ball Joints for 80-96 Ford Bronco, F150, F250 (1 page)
- 4128 - Heavy Duty Ball Joints (1 page)
- 4129/29-01 - Jeep XJ Heavy Duty Front Ball Joints (2 pages)
- 413402 - Low Misalignment Tie Rod End Dust Boot (3 pages)
- 414X - GM HD Ball Joints (1 page)
- 5000 - Jeep TJ Front Coilover Bracket Kit (4 pages)
- 5011 - Jeep JK Front Coil Over Mounting Kit (17 pages)
- 5011-03 - Jeep JK Front Air Bump Mounting Kit (5 pages)
- 5012 - Jeep TJ/YJ/CJ Universal Shock Hoop (6 pages)
- 5013 - Jeep JK Rear Coilover Kit (13 pages)
- 5014-A - Jeep JK Rear Air Bump Kit (10 pages)
- 5016 - Jeep JK Unlimited Three Seat Bracket (7 pages)
- 5017 - 2012+ Jeep JK Exhaust Spacer Kit (9 pages)
- 5019 - Jeep JK Thru Coil Front Air Bump Kit (10 pages)
- 5021 - Jeep JK Heavy Duty Front Lower Control Arm Frame Bracket (10 pages)
- 5022-02 - Jeep JK Frame Side RLCA Gusset Kit (12 pages)
- 5051 - Front 3 Link Kit for Jeep TJ (16 pages)
- 5052 - Rear 4 Link Kit (Bronco, Jeep CJ, TJ, YJ, Universal) (10 pages)
- 5102-0X - Jeep JK Louvered Hood Panel (13 pages)
- 5103 - Jeep JK License Plate Delete Panel (3 pages)
- 5203 - Jeep TJ/LJ Front Cage Kit (10 pages)
- 5204 - Jeep TJ Rear Cage Kit (6 pages)
- 5205 - TJ/LJ Cage Tie-In Kit (4 pages)
- 5210 - Jeep LJ/TJ Cage Kit (8 pages)
- 5221 - 07-10 Jeep JK 2/4 Door Front Cage Kit (51 pages)
- 5221-A - 2011+ Jeep JK 2/4 Door Front Cage Kit (61 pages)
- 5222-04 - Jeep JK 2 Door Weld-In Harness Bar (6 pages)
- 5222-A - Jeep JK 2 Door Rear Cage Kit (10 pages)
- 5223 - JK 4 Door B-Pillar Cage Kit (15 pages)
- 5224-A - Jeep JK 4 Door Rear Cage Kit (11 pages)
- 5232-3 - Jeep YJ Rear Cage Kit (8 pages)
- 523X - Jeep YJ Cage Kit (14 pages)
- 5310 - Jeep JK Rear Bumper (10 pages)