CARR 210344 Light Bar - Manual

Quality and Style that Endures
Follow the diagram and the written
directions carefully for a proper,
safe installation.
Should you encounter an unusual,
unforeseen problem, contact our
Technical Help Line
7:00 AM – 3:00 PM Pacific Time
(951) 719-1068
Visit our web-site at
www.CARR.com
Carr Pattern Co., Inc.
WARNING!
THIS CARR LIGHT BAR IS DESIGNED TO HANDLE A TOTAL
WEIGHT OF FOUR (4) LBS. ANY ADDITIONAL WEIGHT
BEYOND THIS CAPACITY, MAY RESULT IN SERIOUS
DAMAGE TO YOUR VEHICLE AND/OR ANOTHER VEHICLE.
SPECIAL NOTE: VEHICLES NOT HAVING RAIN GUTTERS WILL REQUIRE RAIN GUTTER KITS:
#220042 76-93 Chevy S-10/Sonoma P/U, Blazer/Jimmy, ’09-‘14 Dodge FS 1500 P/U All Cabs, 84-02 Isuzu
Trooper, 97-02 Mitsub. Mont.Sport, 05-14 Toyota Prerunner Cr.Cab, 07-14 Tundra,
05-07 4-Runner, 07-14 FJ Cruiser
#220052 04-14 Chevy Colorado/GMC Canyon, 97-04 Dodge Dakota, 99-14 Ford Super Duty All Cabs, 00-05, Ford
Excursion, 91-02 Isuzu Rodeo/Amigo, 05-14 Jeep Grand Cherokee, 83-93 Mazda B-Series P/U, 98-14
Nissan Frontier Reg.Cab, 98-14 Nissan Frontier Crew Cab, 02-14 Nissan Xterra-w/o Option Roof Rack,
86-01 Pathfinder, 86-97 Nissan Hard Body P/U, 89-95 Toyota P/U, 93-99 T-100, 84-04 Toyota 4-Runner,
96-04 Toyota Tacoma/Prerunner Crew Cab, 00-06 Toyota Tundra, 01-07 Toyota Sequoia.
#220062 04-14 F-150,
#220542 00-14 Chevy/GMC Sierra/Silverado C/K P/U/FS, 01-09 HD, 02-10 Chevy TrailBlazer/Envoy
/Avalanche/GMC/Denali Truck, 00-14 Chevy Tahoe/Suburban/Tahoe/GMC Yukon/Yukon XL, 02-08
Dodge FS 1500 P/U, 03-14 Dodge 2500/3500 P/U & Quad, 02-08 Dodge Quad 1500, 05-09 Dodge
Durango/Dakota, 06-14 Dodge Mega Cab 1500/2500/3500 Ram P/U
#221502 98-01 Dodge Quad Cab 1500 P/U, 98-02 Dodge Quad Cab 2500/3500 P/U, 94-02 Dodge 2500/3500 P/U
Old Body Style, 94-01 Dodge P/U.
#222742 91-01 Ford Explorer(not Eddie Bauer)/Mercury Mountineer, 91-94 Mazda Navajo,
#223412 88-99 Sierra Silverado C&K P/U/FS, 92-99 Chevy Suburban/Yukon/Tahoe, 93-98 Jeep Grand Cherokee
LIGHT BAR CUTTING INSTRUCTIONS
1. Two people will be needed to complete this task.
2. Place ONLY THE MOUNTING END CASTINGS with the Rubber Booties into the rain-gutters.
3. Level each Mounting End Casting so that the top flat area is parallel to the horizon.
4. Take a tape measure and measure the distance between each open end of each Mounting End Casting .
5. Add 2 inches to that dimension.
6. Subtract that total from the total length of the bar, which is 56".
7. Take the difference and divide it by two.
8. The amount divided by two is the amount you will cut off each end of your bar.
MATERIALS NEEDED: Hammer,
center punch, pencil
MATERIALS FURNISHED: One
hardware pack, two end castings, cross
bar, instruction page.
LIGHT BAR MOUNTING INSTRUCTIONS
Part No’s: 210341, 210342 & 210344
This is the open end of the Mounting End
Casting. Measure from this point on each
Mounting End Casting. (See below for Light
Bar Cutting Instruction)
¼” Bolts
For the proper installation of
this light bar, orientation of this
washer must be as shown in this
drawing
Cross Bar
“L” Shaped Steel
Bracket
Rubber Bootie
3/16” Allen Wrench
5/16” Bolt
Mounting End Casting