Gradall 524D - Manual (Page 184)

522D-524D
MATERIAL HANDLER
Item Part No. Qty. Description Of Part
105 9112-1082 8 SHIM
106 9112-3021 2 BEARING PAD, 1/2-x6”
107 9108-3063 4 BEARING PAD, 5/8x8”
108 9103-3187 1 BEARING PAD, 5/8x3-1/4
109 8820-1534 4 HEX HD CAPSCREW, 3/8-24x1”,
GR5 (lubricate & torque to
32-37 ft. lbs.)
110 8820-1562 6 HEX HD CAPSCREW, 1/2-20x3/4,
GR5 (lubricate & torque to
68-78 ft. lbs.)
111 8820-1568 4 HEX HEAD CAPSCREW,
1/2-20x2”, GR5 (lubricate & torque
to 68-78 ft. lbs.)
112 9108-1172 4 SPACER
113 8820-1046 1 HEX HEAD CAPSCREW,
3/8-16x3-3/4, GR5
114 9112-6071 1 HOSE GUARD
115 8856-1111 4 WASHER, 1/2
116 9112-1157 2 SHIM
117 9108-1171 2 SHIM
118 8863-1337 1 COTTER PIN, 3/16x1-1/2
119 8867-1002 2 LUBE FITTING
120 8688-1276 2 90 DEGREE TUBE FITTING
121 8688-1273 2 STRAIGHT TUBE FITTING
122 7208-8049 20” NYLON TUBE FITTING, 1/4
123 9103-3445 1 LUBE FITTING
124 8871-2011 1 90 DEGREE ELBOW
125 8320-1038 4 HEX HD CAPSCREW, 3/4-10x2-1/4,
GR8
Item Part No. Qty. Description Of Part
83 9020-6199 TRIM-LOCK, 13”
84 9020-6194 TRIM-LOCK, 3.5’
85 1440-2248 AR 3M-ADHESIVE
86 9002-7179 4 90 DEGREE BULKHEAD FITTING
87 9112-1125 1 BULKHEAD BRACKET
88 8820-1020 2 HEX HEAD CAPSCREW,
5/16-18x1”, GR5
89 8855-1010 2 LOCKWASHER, 5/16
90 8850-1005 2 HEX NUT, 5/16-18
91 9112-6009 1 EXTEND CABLE BRACKET
92 8852-1208 4 HEAVY LOCKNUT, 1/2-13
93 9112-1196 1 EXTEND CABLE PIN
94 9112-5030 2 EXTEND SHEAVE ASSEMBLY
95 9112-1045 2 RETAINER ROLLER
96 8320-1073 1 HEX HEAD CAPSCREW,
3/8-16x4-1/2, GR8
97 9108-3432 1 RETRACTION CABLE (includes
item 118)
98 1440-4595 AR UNION 76 MEGAPLEX GREASE
99 9108-1087 1 CABLE ADJUSTMENT BLOCK
(lubricate & torque to 68-78 ft. lbs.)
100 8320-1026 4 HEX HD CAPSCREW, 1/2-13x1-1/2,
GR8 (lubricate & torque to
68-78 ft. lbs.)
101 9103-3185 2 BEARING PAD, 3/4x6”
102 8855-1013 1 LOCKWASHER, 1/2
103 8859-1207 2 O-RING
104 9112-1083 4 SPACER
13-11
OPTIONAL EQUIPMENT
(9138-5002) 3 Section Boom Assembly
Original Issue 1-98
Revised 11-08-05
!
NOTE: ADD BEARING PAD SHIMS & SPACERS AS REQUIRED
TO SHIM BOOM TO WITHIN 1/16” OF A TIGHT FIT. AMOUNTS
OF SHIMS CAN VARY AT EACH SHIM POINT. WHENEVER A
SHIM IS USED WITH A PAD, A SPACER MUST BE INSERTED
BETWEEN PAD AND SHIM. NO PADS SHALL SIT DIRECTLY ON
SLOTTED SURFACE OF SHIMS.
JD
* Added seal kits to item 41.