Gradall 534D-6T Parts Manual User Manual
Page 238
13-29
DS
Item
Part No.
Qty.
Description Of Part
9114-3267
1
CAB ENCLOSURE KIT, (includes all
items on pages 13-28 thru 13-30)
9114-4469
1
LATCH RETRO FIT KIT, (includes
items 31, 41 thru 48 & 50)
9133-4007
1
L.H. SIDE ASSY, (includes all items
on page 13-29)
9134-4010
1
UPPER DOOR ASSY, (includes items
1 thru 13)
9134-4011
1
LOWER DOOR ASSY, (includes items
24, 31, 32 and 37 thru 56)
9133-4012
1
DOOR HOLD OPEN ASSY, (includes
items 27 thru 30)
1
9134-4012
1
UPPER FRAME ASSY, (painted)
2
9134-4013
1
WINDOW LATCH ASSY, (includes
items 14 thru 19 & item 12 as
required)
3
8026-4091
21.5 BULB SEAL, 90 DEGREE
4
Ref
GLASS, (see page 13-30 for details)
5
9134-4014
.17'
FOAM, .438X.375
6
9133-4034
AR
BLACK URETHANE
7
8026-4084
1
GROMMET, .51X1.06
8
9134-4015
1
BUSHING
9
8026-4082
1
WASHER
10
9134-4016
1
DOOR ANGLE
11
9134-4017
2
SCREW, .25-20X1.25
12
9134-4018
AR
LOCTITE, BLUE
13
9134-4019
1
GROMMET, .375X.875
14
9134-4020
1
NUT, .25-20, GR5
15
9134-4021
1
BOLT, .375-16X1.00
16
9134-4022
2
STEEL LATCH
17
9134-4023
1
POLYURETHANE LATCH
18
8026-4108
1
KNOB
19
9134-4024
1
SCREW, .25X1.00
20
9114-4435
1
CAB KIT SERIAL TAG
21
9134-4025
1
FOAM, L.H. SIDE PANEL
22
9134-4026
AR
ADHESIVE, HIGH PERFORMANCE
Item
Part No.
Qty.
Description Of Part
23
9133-4018
2
LOCKNUT, .375-16
24
9134-4027
1
DOOR STRAP
25
9133-4033
3
FLAT WASHER, .375X.88
26
9133-4018
2
LOCKNUT, .375-16
27
9134-4028
1
DOOR HOLD BRACKET WELD
28
9134-4029
1
DOOR HOLD OPEN ROD
29
9134-4019
1
GROMMET, .375X.875
30
9134-4030
1
COTTER PIN, 1/8X.75
31
9148-4028
1
PADDLE LATCH, (see illustration &
notes at top of page)
32
8096-4051
1
DOOR KEY, #510, (old style latch)
9114-4470
1
DOOR KEY, CH 751, (new style latch)
33
9134-4031
7.5'
BULB SEAL, 1/4 CLIP
34
Ref
GLASS, (see page 13-30 for details)
35
8026-4033
2
WINDOW CLIP
36
8026-4034
4
SCREW, #10-32X1.50
37
9134-4043
6
SCREW, .25-20X.625
38
9134-4032
1
GRAB HANDLE, (inside)
39
9134-4033
.25"
FOAM, PSA 3/16X5/8
40
9148-4030
1
LOWER DOOR WELDMENT
41
9148-4029
1'
BULB SEAL
42
9148-4034
2
MOUNTING BRACKET
43
8038-4191
4
SCREW, 10-24X.5
44
8038-4187
1
ROD RETAINER CLIP
45
9148-4036
1
CAM LATCH
46
9148-4035
1
LINKAGE ROD
47
8038-4185
1
ROD RETAINER CLIP
48
8026-4074
4
SCREW, .25-20X.75
49
8026-4046
4
NUT, .25-20
50
9148-4031
1
CENTER STIFFENER COVER
51
9116-4096
2
SCREW, .25-20X.75
52
9134-4047
1
LOWER DOOR FOAM
53
9134-4046
AR
BLACK URETHANE
54
9134-4045
2
VINYL CAP
55
9148-4024
6'
BULB SEAL
56
8026-4091
2.5'
BULB SEAL
* Total revision of page.
9134-3056
INSIDE & OUTSIDE LATCH KIT
USED ON CAB ENCLOSURE KITS
PRIOR TO ANGUS-PALM S/N T2702A &
ENCLOSED CABS PRIOR TO S/N P9623M
1) Remove door stiffener cover and mounting hardware.
2) Remove inside door release mounting hardware. Including
(1) .25-20x1.00 screw, (1) .28 ID x 1.00 OD washer, (1) nylon
bushing, (2) .406 ID x 1.25 OD washers, (2) .312-18 lock nut,
(1) plate, door link, and (1) .25-20 lock nut.
3) Install new inside door release hardware as shown.
4) Reverse spring attachment as shown.
5) Replace door stiffener cover and hardware.
MOVE LATCH UP - FIRE SOONER
MOVE LATCH DN - FIRE LATER
ADJUST STRIKER STUD TO ALIGN
WITH CAM LATCH JAWS
FURTHER ADJUSTMENT:
LOOSEN CAP SCREWS
MOVE CAM
RETIGHTEN - SET CLUTCH
ON CORDLESS DRIVER TO
_ FT LBS
HEX NUT 25-20
HAND TIGHTEN TO
BUSHING & JAM TIGHTEN
TO END NUT(retain)
AT LEAST 1/2
STROKE TRAVEL IS
OPTIMAL
REPLACE PLATE LINK
WASHER, .28IDx1.50OD
(retain)
DISCARD OLD
BOLT & REPLACE
WITH LONGER BOLT.
WHEN INSTALLED
BOLT SHOULD BE
TIGHT & NOT GIVE.
DISCARD OLD
NYLON BUSHING &
REPLACE WITH STEEL
BUSHING MUST TURN FREELY
BOLT .312-18 (REF)
RETAIN
THE INSIDE DOOR RELEASE MAY NEED TO
BE ADJUSTED LATERALLY BY WAY OF THE
SLOTTED HOLES, TO AFFECT PROPER ACTUATION
FROM EXTERIOR PADDLE LATCH HALF STROKE
LINK PLATE GOES BEHIND
CAM LATCH LEVER
BEND OUTWARD SLIGHTLY TO
ENSURE LINK PLATE RIDES
AGAINST WASHER & NOT ON NUT
CAM, LATCH (REF)
PADDLE LATCH SHOULD ACTUATE CAM
LATCH AT HALF STROKE TRAVEL (OPTIONAL)
ENSURE STAKE PIVOT IS
COMPRESSED FIRMLY TO LATCH
BODY AND IS NOT LOOSE
(IF LOOSE, REPLACE LATCH)
NUT, LOCK 25-20 (RETAIN)
SPRING (REF)
PADDLE LATCH INSTALLATION
USED ON CAB ENCLOSURE KITS WITH
ANGUS-PALM STARTING S/N T2702A &
ENCLOSED CABS STARTING S/N P9623M
NOTE: IF YOUR CAB ENCLOSURE CONTAINS THE LATCH
ASSY, (shown left), IT IS RECOMMENDED TO
UPDATE TO CURRENT STYLE, (shown below), BY
ORDERING LATCH RETRO FIT KIT, 9114-4469, (see
parts list for details).
OPTIONAL EQUIPMENT
(9114-3267) Cab Enclosure Kit
534D-6 Starting Serial No. 0588001
534D-6 TURBO Starting Serial No. 0588008
Original Issue 5-98
Revised 7-13-01